Sony ICD-UX70RED Operating Instructions - Page 50

Symptom, Remedy, When recording

Get Sony ICD-UX70RED - Digital Voice Recorder PDF manuals and user guides View all Sony ICD-UX70RED manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Symptom Remedy "FILE FULL" is displayed and you cannot operate the IC recorder.  99 messages have been recorded in the selected folder or 495 messages (when there are 5 folders) in total have been recorded. Therefore you cannot record another message, or move a message. Erase some of the messages (page 29) or erase all the messages after you store them on your computer. Recording is interrupted.  The VOR function (page 19) is activated. Set "VOR" to "OFF" in the menu (page 35). Noise is heard.  An object, such as your finger, etc., accidentally rubbed or scratched the IC recorder during recording so that noise was recorded.  The IC recorder was placed near an AC power source, a fluorescent lamp or a mobile phone during recording or playback.  Plug of the connected microphone was dirty when recording. Clean the plug.  The  (headphones) plug is dirty. Clean the plug. Recording level is low.  "MIC SENS" (microphone sensitivity) is set to "LOW (L)". Display the menu and set "MIC SENS" to "HIGH (H)" (page 35). When recording from other equipment, the input level is too strong or not strong enough.  Connect the headphone jack of other equipment to the  (microphone) jack of the IC recorder and adjust the volume level on the equipment connected to the IC recorder. Playback speed is too fast  The playback speed is adjusted in DPC. Slide the DPC switch to or too slow. "OFF" or display the menu and adjust the speed in DPC again (pages 26, 36). "--:--" is displayed.  You have not set the clock (page 14). "--y--m--d" or " --:--" is displayed on the REC DATE display.  The date of recording will not be displayed if you recorded the message when the clock was not set. 50GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
³0
GB
Symptom
Remedy
“FILE FULL” is displayed
and you cannot operate
the IC recorder.
99 messages have been recorded in the selected
folder or
495 messages (when there are 5 folders) in total have been
recorded. Therefore you cannot record another message, or
move a message. Erase some of the messages (page 29) or
erase all the messages after you store them on your computer.
Recording is interrupted.
The VOR function (page 19) is activated. Set “VOR” to “OFF” in
the menu (page 35).
Noise is heard.
An object, such as your finger, etc., accidentally rubbed or
scratched the IC recorder during recording so that noise was
recorded.
The IC recorder was placed near an AC power source, a
fluorescent lamp or a mobile phone during recording or
playback.
Plug of the connected microphone was dirty when recording.
Clean the plug.
The
(headphones) plug is dirty. Clean the plug.
Recording level is low.
“MIC SENS” (microphone sensitivity) is set to “LOW (L)”.
Display the menu and set “MIC SENS” to “HIGH (H)” (page 35).
When recording from
other equipment, the
input level is too strong or
not strong enough.
Connect the headphone jack of other equipment to the
(microphone) jack of the IC recorder and adjust the volume
level on the equipment connected to the IC recorder.
Playback speed is too fast
or too slow.
The playback speed is adjusted in DPC. Slide the DPC switch to
“OFF” or display the menu and adjust the speed in DPC again
(pages 26, 36).
“--:--” is displayed.
You have not set the clock (page 14).
“--y--m--d” or ” --:--” is
displayed on the REC
DATE display.
The date of recording will not be displayed if you recorded the
message when the clock was not set.