Sony KLV-S20G10 Operating Instructions - Page 34

Programming the Remote Control, button VCR/DVD or SAT/CABLE will

Get Sony KLV-S20G10 - 20inch Lcd Wega Flat Panel Television PDF manuals and user guides View all Sony KLV-S20G10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Watching the TV Programming the Remote Control The remote control is preset to operate Sony brand video equipment. Sony Equipment VCR/DVD SAT/CABLE Programmable Code Number 301 (Sony VCR) 801 (Sony Satellite Receiver) Follow the steps below to program your TV's remote control to operate non- 3 Sony video equipment. The equipment must have infrared (IR) remote capability in order to be used with this remote control. 4 Find the three-digit code for your equipment from the "Manufacturer's Codes" listed on page 35. If more than one code number is listed, try entering from the code listed first. 1 Press CODE SET. 2 Press the or FUNCTION button you want to program on 2 the remote control. The selected FUNCTION button (VCR/DVD or SAT/CABLE) will flash. 3 Enter the three-digit manufacturer's code number using the --9 buttons while the button is lit (approximately 10 seconds). 4 Press button. When the programming is correct, the selected FUNCTION button will flash twice slowly, and when not, flashes five times quickly. 1 To check if the code works Aim your TV's remote control at the equipment, and press the VCR/DVD and/or SAT/CABLE (POWER) button that corresponds with the equipment. If the equipment responds, the programming is completed. If not, try the next code listed. Insert two size AA batteries (supplied) by matching the e and E on the batteries to the diagram inside the remote control's battery compartment. If you enter a new code number, the code number you previously entered at that setting is erased. If no code is input within the above specified time, or an invalid or incorrect code number is input, the remote control automatically goes back to the previous setting. In some cases, you may not be able to program your remote control to operate other equipment. In such cases, use the equipment's own remote control. Dead batteries or removing the batteries may cause the programmable codes to be lost and revert back to factory settings. Reprogramming the codes may be necessary. 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
Watching the TV
34
Programming the Remote Control
The remote control is preset to operate Sony brand video equipment.
Follow the steps below to program your TV’s remote control to operate non-
Sony video equipment.
Find the three-digit code for your equipment from the “Manufacturer’s
Codes” listed on page 35. If more than one code number is listed, try
entering from the code listed first.
1
Press
CODE SET
.
2
Press the
or
FUNCTION
button you want to program on
the remote control.
The selected
FUNCTION
button (VCR/DVD or SAT/CABLE) will
flash.
3
Enter the three-digit manufacturer’s code number using the
-
-
9
buttons while the button is lit (approximately 10 seconds).
4
Press
button.
When the programming is correct, the selected
FUNCTION
button will
flash twice slowly, and when not, flashes five times quickly.
To check if the code works
Aim your TV’s remote control at the equipment, and press the VCR/DVD
and/or SAT/CABLE (POWER) button that corresponds with the equipment.
If the equipment responds, the programming is completed. If not, try the
next code listed.
Sony Equipment
Programmable Code Number
VCR/DVD
301 (Sony VCR)
SAT/CABLE
801 (Sony Satellite Receiver)
The equipment must have infrared (IR) remote capability in order
to be used with this remote control.
If you enter a new code number, the code number you previously
entered at that setting is erased.
If no code is input within the above specified time, or an invalid or
incorrect code number is input, the remote control automatically
goes back to the previous setting.
In some cases, you may not be able to program your remote
control to operate other equipment. In such cases, use the
equipment’s own remote control.
Dead batteries or removing the batteries may cause the
programmable codes to be lost and revert back to factory settings.
Reprogramming the codes may be necessary.
3
4
2
1
Insert two size AA batteries
(supplied) by matching the
e
and
E
on the batteries to the
diagram inside the remote
control’s battery compartment.