Sony MEXBT2700 Operating Instructions - Page 14

Bluetooth operations, Pairing - xplod

Get Sony MEXBT2700 - CD Receiver With Bluetooth Hands-Free PDF manuals and user guides
UPC - 027242744899
View all Sony MEXBT2700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Bluetooth function Bluetooth operations To use the Bluetooth function, the following procedure is necessary. 1 Pairing When connecting Bluetooth devices for the first time, mutual registration is required. This is called "pairing." This registration (pairing) is required only for the first time, as this unit and the other devices will recognize each other automatically from the next time. You can pair up to 8 devices. (Depending on the device, you may need to input a passcode for each connection.) 2 Connection To use the device after pairing is made, start the connection. Sometimes pairing allows to connect automatically. 3 Handsfree calling/Music streaming You can talk handsfree and listen to music when the connection is made. Support site http://esupport.sony.com http://www.xplodsony.com/ Pairing First, register ("pair") a Bluetooth device (cellular phone, etc.) and this unit with each other. You can pair up to 8 devices. Once pairing is established, there is no need for pairing again. 1 Place the Bluetooth device within 1 m (3 ft) of this unit. 2 Press and hold (BT) until " " flashes (about 5 seconds). The unit enters pairing standby mode. flashing 3 Set the Bluetooth device to search for this unit. A list of detected devices appears in the display of the device to be connected. This unit is displayed as "XPLOD" on the device to be connected. DR-BT30Q XPLOD XXXXXXX 4 If Passcode* input is required on the display of the device to be connected, input "0000." XXXX Input passcode. "0000" This unit and the Bluetooth device memorize each other's information, and when pairing is made, the unit is ready for connection to the device. " " flashes and then stays lit after pairing is complete. 5 Set the Bluetooth device to connect to this unit. " " or " " appears when the connection is made. * Passcode may be called "passkey," "PIN code," "PIN number" or "Password," etc., depending on the device. Note Pairing standby mode is not released until the connection is made. About Bluetooth icons The following icons are used by this unit. lit: Bluetooth signal on flashing: Pairing standby mode off: Bluetooth signal off lit: Connection successful flashing: Connecting off: No connection lit: Connection successful flashing: Connecting off: No connection 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
14
Bluetooth function
Bluetooth operations
To use the Bluetooth function, the following
procedure is necessary.
1
Pairing
When connecting Bluetooth devices for the
first time, mutual registration is required. This
is called “pairing.” This registration (pairing)
is required only for the first time, as this unit
and the other devices will recognize each
other automatically from the next time. You
can pair up to 8 devices. (Depending on the
device, you may need to input a passcode for
each connection.)
2
Connection
To use the device after pairing is made, start
the connection. Sometimes pairing allows to
connect automatically.
3
Handsfree calling/Music streaming
You can talk handsfree and listen to music
when the connection is made.
Pairing
First, register (“pair”) a Bluetooth device
(cellular phone, etc.) and this unit with each
other. You can pair up to 8 devices. Once pairing
is established, there is no need for pairing again.
1
Place the Bluetooth device within 1 m
(3 ft) of this unit.
2
Press and hold
(BT)
until “
” flashes
(about 5 seconds).
The unit enters pairing standby mode.
3
Set the Bluetooth device to search for
this unit.
A list of detected devices appears in the
display of the device to be connected. This
unit is displayed as “XPLOD” on the device
to be connected.
4
If Passcode
*
input is required on the
display of the device to be connected,
input “0000.”
This unit and the Bluetooth device memorize
each other’s information, and when pairing is
made, the unit is ready for connection to the
device.
“
” flashes and then stays lit after pairing is
complete.
5
Set the Bluetooth device to connect to
this unit.
“
” or “
” appears when the connection is
made.
*
Passcode may be called “passkey,” “PIN code,” “PIN
number” or “Password,” etc., depending on the
device.
Note
Pairing standby mode is not released until the
connection is made.
About Bluetooth icons
The following icons are used by this unit.
Support site
flashing
lit:
flashing:
off:
Bluetooth signal on
Pairing standby mode
Bluetooth signal off
lit:
flashing:
off:
Connection successful
Connecting
No connection
lit:
flashing:
off:
Connection successful
Connecting
No connection
XXXXXXX
DR-BT30Q
XPLOD
XXXX
Input passcode.
“0000”