Sony PCNA-MR10 User Guide - Page 29

To attach the ferrite core, Wrap the network cable twice around the ferrite core, lengthwise, with

Get Sony PCNA-MR10 - Roomlink PDF manuals and user guides View all Sony PCNA-MR10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Setting Up RoomLink Attaching the ferrite core In accordance with FCC Rules, Part 15, a ferrite core is supplied with the network media receiver. The ferrite core should be attached to the network cable*, to reduce or eliminate electrical interference. 1 Open the ferrite core and place the core approximately 3-4 inches from the end of the network cable. 2 Wrap the network cable twice around the ferrite core, lengthwise, with the cable running directly through the center groove of the core. 3 Close the ferrite core tightly around the network cable until the core locks. To attach the ferrite core Ferrite core Ethernet port * The network cable must be compatible with the 100BASE-TX standard. 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
Setting Up RoomLink
29
Attaching the ferrite core
In accordance with FCC Rules, Part 15, a ferrite core is supplied with the
network media receiver. The ferrite core should be attached to the network
cable
*
, to reduce or eliminate electrical interference.
1
Open the ferrite core and place the core approximately 3-4 inches from the
end of the network cable.
2
Wrap the network cable twice around the ferrite core, lengthwise, with the
cable running directly through the center groove of the core.
3
Close the ferrite core tightly around the network cable until the core locks.
*
The network cable must be compatible with the 100BASE-TX standard.
To attach the ferrite core
Ferrite core
Ethernet port