Sony PCNA-MR10 User Guide - Page 30

Setting up the Remote Commander unit, To program the Remote Commander - remote code

Get Sony PCNA-MR10 - Roomlink PDF manuals and user guides View all Sony PCNA-MR10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

RoomLink User Guide Setting up the Remote Commander unit 1 Open the battery cover on the back of the Remote Commander® unit. 2 Insert two AA batteries (supplied) by matching the + and - on the batteries, with the diagram inside the battery compartment. Inserting batteries into the Remote Commander ✍ Under normal use, the AA batteries may last up to six months. If your Remote Commander does not operate properly, the batteries may need replacing. If your Remote Commander is not being used for long periods of time, remove the batteries to avoid possible damage from leaking batteries. To program the Remote Commander Your Remote Commander® unit is preprogrammed to control certain TVs. Refer to your TV manufacturer's code table for more information. The Remote Commander may not be compatible with some TV models, even when the appropriate TV manufacturer code is entered. 1 Press and hold the SELECT button. 2 Enter your TV code number, using the channel number buttons. 3 Release the SELECT button after you have entered the TV code number. ✍ After replacing the batteries in your Remote Commander, the TV manufacturer's code may require resetting. Reset the code each time you replace the batteries. 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
RoomLink User Guide
30
Setting up the Remote Commander unit
1
Open the battery cover on the back of the Remote Commander® unit.
2
Insert two AA batteries (supplied) by matching the + and - on the batteries,
with the diagram inside the battery compartment.
To program the Remote Commander
Your Remote Commander® unit is preprogrammed to control certain TVs. Refer
to your TV manufacturer’s code table for more information. The Remote
Commander may not be compatible with some TV models, even when the
appropriate TV manufacturer code is entered.
1
Press and hold the
SELECT
button.
2
Enter your TV code number, using the channel number buttons.
3
Release the
SELECT
button after you have entered the TV code number.
Inserting batteries into the Remote Commander
✍
Under normal use, the AA batteries may last up to six months. If your Remote
Commander does not operate properly, the batteries may need replacing. If your
Remote Commander is not being used for long periods of time, remove the batteries
to avoid possible damage from leaking batteries.
✍
After replacing the batteries in your Remote Commander, the TV manufacturer
’
s code
may require resetting. Reset the code each time you replace the batteries.