Sony PCV-J200 System Reference Manual - Page 53

Installing a 3.5” Internal Hard Disk Drive, Disconnect the power cord from the computer.

Get Sony PCV-J200 - Vaio Desktop Computer PDF manuals and user guides View all Sony PCV-J200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Removing, Installing, and Replacing Components 41 Installing a 3.5" Internal Hard Disk Drive Your system comes with an available bay to hold an additional 3.5" IDE hard disk drive. Some models, such as Configure-to-Order (CTO) systems, may already have a second hard disk drive. Your system can support ATA-33, ATA-66, or ATA-100 hard disk drives. The drive you install must not require front panel access. The hard disk drive access light blinks when either internal drive is active. ! Before opening the system unit, save and close all open files, exit all open applications, turn off the power to all attached peripheral devices, shut down the computer, and unplug the power cord. 1 Configure the jumpers on the new drive as a slave device (see your drive's documentation for configuration instructions). Power connector Jumpers Drive connector 2 Disconnect the power cord from the computer. 3 Remove the side panel (see "Removing the Side Panel" on page 22). 4 Lift the tab adjacent to the drive holder.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Removing, Installing, and Replacing Components
41
Installing a 3.5” Internal Hard Disk Drive
Your system comes with an available bay to hold an additional 3.5” IDE
hard disk drive. Some models, such as Configure-to-Order (CTO)
systems, may already have a second hard disk drive.
Your system can support ATA-33, ATA-66, or ATA-100 hard disk drives.
The drive you install must not require front panel access. The hard disk
drive access light blinks when either internal drive is active.
1
Configure the jumpers on the new drive as a slave device (see your
drive’s documentation for configuration instructions).
2
Disconnect the power cord from the computer.
3
Remove the side panel (see
“Removing the Side Panel”
on page 22).
4
Lift the tab adjacent to the drive holder.
!
Before opening the system unit, save and close all open files, exit all open
applications, turn off the power to all attached peripheral devices, shut
down the computer, and unplug the power cord.
Power connector
Jumpers
Drive connector