Sony RDHSK8IP Operating Instructions - Page 15

General, iPod/iPhone, The indicator does not stop flashing - model

Page 15 highlights

Troubleshooting General The indicator does not light up. • Make sure you press the POWER on the back panel. • Disconnect the AC power cord (mains lead), then check that the voltage selector is set to the local power supply voltage (page 8). There is severe noise. • Someone is using a portable telephone or other equipment that emits radio waves near the unit. Move the portable telephone, etc. away from the unit. The remote does not function. • Remove any obstacles in the path of the unit and the remote. • Point the remote at the remote sensor of the unit. • Replace the battery. • Locate the unit away from fluorescent lights. • Place the iPod/iPhone to the connector firmly. iPod/iPhone If the iPod/iPhone does not operate properly, check that you have removed the protect case of the iPod/iPhone. If the problem persists, use the following troubleshooting guide to remedy the problem. There is no sound. • Make sure you press the POWER on the back panel. • Make sure the iPod/iPhone is connected firmly. • Make sure the iPod/iPhone is playing music. • Press VOL + (or VOLUME + on the unit) repeatedly. • Depending on the contents of the iPod/ iPhone, it may take time to start playback. • You are using an unsupported iPod/ iPhone. See "Compatible iPod/iPhone models with this unit" (page 18) for the supported device types. The sound is distorted. • Press VOL - (or VOLUME - on the unit) repeatedly. • Set the "EQ" setting of the iPod/iPhone to "Off" or "Flat". The iPod/iPhone cannot be charged. • Make sure you press the POWER on the back panel. • Make sure the iPod/iPhone is connected firmly. The indicator does not stop flashing when the iPod/iPhone is connected. • A problem has been detected with the level of electrical current from the iPod/iPhone. Turn off the unit and remove the iPod/iPhone. Make sure there is no problem with the iPod/ iPhone. If this problem persists, contact your nearest Sony dealer. The iPod/iPhone cannot be operated. • Disconnect the iPod/iPhone and connect the iPod/iPhone again. • You are using an unsupported iPod/ iPhone. See "Compatible iPod/iPhone models with this unit" (page 18) for the supported device types. The ring volume of the iPhone does not change. • Adjust the ring volume using the controls on the iPhone. Continued l 15GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20

15
GB
Troubleshooting
General
The indicator does not light up.
Make sure you press the POWER on the
back panel.
Disconnect the AC power cord (mains
lead), then check that the voltage
selector is set to the local power supply
voltage (page 8).
There is severe noise.
Someone is using a portable telephone
or other equipment that emits radio
waves near the unit. Move the portable
telephone, etc. away from the unit.
The remote does not function.
Remove any obstacles in the path of the
unit and the remote.
Point the remote at the remote sensor of
the unit.
Replace the battery.
Locate the unit away from fluorescent
lights.
Place the iPod/iPhone to the connector
firmly.
iPod/iPhone
If the iPod/iPhone does not operate
properly, check that you have removed
the protect case of the iPod/iPhone. If the
problem persists, use the following
troubleshooting guide to remedy the
problem.
There is no sound.
Make sure you press the POWER on the
back panel.
Make sure the iPod/iPhone is connected
firmly.
Make sure the iPod/iPhone is playing
music.
Press VOL + (or VOLUME + on the
unit) repeatedly.
Depending on the contents of the iPod/
iPhone, it may take time to start
playback.
You are using an unsupported iPod/
iPhone. See “Compatible iPod/iPhone
models with this unit” (page 18) for the
supported device types.
The sound is distorted.
Press VOL – (or VOLUME – on the
unit) repeatedly.
Set the “EQ” setting of the iPod/iPhone
to “Off” or “Flat”.
The iPod/iPhone cannot be charged.
Make sure you press the POWER on the
back panel.
Make sure the iPod/iPhone is connected
firmly.
The indicator does not stop flashing
when the iPod/iPhone is connected.
A problem has been detected with the
level of electrical current from the
iPod/iPhone. Turn off the unit and
remove the iPod/iPhone. Make sure
there is no problem with the iPod/
iPhone. If this problem persists, contact
your nearest Sony dealer.
The iPod/iPhone cannot be operated.
Disconnect the iPod/iPhone and connect
the iPod/iPhone again.
You are using an unsupported iPod/
iPhone. See “Compatible iPod/iPhone
models with this unit” (page 18) for the
supported device types.
The ring volume of the iPhone does
not change.
Adjust the ring volume using the
controls on the iPhone.
Continued
l