Sony SRG120DH Technical Manual - Page 15

Address Set, Memory Preset, Digital Zoom On/Off

Get Sony SRG120DH PDF manuals and user guides View all Sony SRG120DH manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Address Set VISCA is a protocol, which supports a daisy chain of up to seven connected cameras via RS-232 interface. In such cases, the address set command can be used to assign addresses from 1 to 7 to each of the seven cameras, allowing you to control the seven cameras with the same personal computer. Be sure to use the address set command to set the address whenever a camera is connected for the first time. Memory (Preset) Using the preset function, 16 sets of camera shooting conditions can be stored and recalled. This function allows you to achieve the desired status instantly, even without adjusting the following items each time. • Pan/Tilt Position • Zoom Position • Digital Zoom On/Off • Focus Auto/Manual • Focus Position • AE Mode • Shutter control parameters • Bright Control • Iris control parameters • Gain control parameters • Exposure Compensation On/Off • Exposure Level • Backlight Compensation On/Off • Auto Slow Shutter On/Off • White Balance Mode • R/B Gain • Aperture Control • WD Parameter • Defog On/Off The settings stored using this function are recalled when the power is turned on. For setting items, see the "Initial Settings, Custom Preset and Backup" section on page 16. Note Rewriting of memory is not unlimited. Be careful to avoid using the memory area for such as unnecessary tasks as rewriting the contents of the memory for every operation. Basic Functions 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
Basic Functions
1´
Address Set
VISCA is a protocol, which supports a daisy chain of up to
seven connected cameras via RS-232 interface. In such cases,
the address set command can be used to assign addresses
from 1 to 7 to each of the seven cameras, allowing you to
control the seven cameras with the same personal computer.
Be sure to use the address set command to set the address
whenever a camera is connected for the first time.
Memory (Preset)
Using the preset function, 16 sets of camera shooting
conditions can be stored and recalled.
This function allows you to achieve the desired status
instantly, even without adjusting the following items
each time.
•
Pan/Tilt Position
•
Zoom Position
•
Digital Zoom On/Off
•
Focus Auto/Manual
•
Focus Position
•
AE Mode
•
Shutter control parameters
•
Bright Control
•
Iris control parameters
•
Gain control parameters
•
Exposure Compensation On/Off
•
Exposure Level
•
Backlight Compensation On/Off
•
Auto Slow Shutter On/Off
•
White Balance Mode
•
R/B Gain
•
Aperture Control
•
WD Parameter
•
Defog On/Off
The settings stored using this function are recalled
when the power is turned on.
For setting items, see the “Initial Settings, Custom Preset
and Backup” section on page 16.
Note
Rewriting of memory is not unlimited. Be careful to avoid using the
memory area for such as unnecessary tasks as rewriting the
contents of the memory for every operation.