Sony SRPX700P Product Manual (SRP-X700P Hardware Operation Manual 1.3) - Page 7

0 Video output terminals The video signal that is selected by the LINE 4 SELECT button on the front panel is output from this terminal. (The video signal format is not converted from each other.) • 5BNC output terminals The RGB and component signal output terminals. • VIDEO terminal The composite signal output terminal. • S VIDEO terminal The S VIDEO signal output terminal. qa CONTROL S OUTPUT 1 to CONTROL S OUTPUT 4 terminals You can control AV equipments connected to the LINE 3 IN terminal and LINE 4 INPUT terminal by remote control through these terminals. Note The AV equipment connected to the LINE3 IN terminal cannot be controlled from supplied software User Control Panel. You can perform the basic operations of Sony DVD, VCR, CD, MD and CD-R audio, such as playback, stop, fast forward and rewind. You can select either the wired connection or the wireless connection for each terminal from the SRP-X700P Manager. qs PROJECTOR CONTROL terminals The SRP-X700P can controls a applicable projector and plasma display connected to the video output terminals from this terminal. By default, connection to use the VPL-FX50 is set through RS-232C. • RS-232C terminal This terminal is for a projector or plasma display having the RS-232C terminal. • CONTROL S IN/OUT terminal The SRP-X700P can control a projector without the RS232C terminal through the CONTROL S. When controlling a projector using the CONTROL S OUT terminal, mixed use of the component signal and the RGB signal is not possible. qd REMOTE PARALLEL terminal The parallel remote terminal contains 12 INPUTs and 10 OUTPUTs. You can control the SRP-X700P from external remote equipment using the INPUT parallel remote pins. You can control the external remote equipment from the SRP-X700P using the OUTPUT parallel remote pins. You can select the functions of the respective terminals using the supplied SRPX700P Manager software. qf REMOTE RS-232C terminal The RS-232C remote terminal. You can control the SRP-X700P with external equipment connected to the RS-232C terminal from a remote location. qg REMOTE USB terminal You can connect a personal computer in which the supplied software (SRP-X700P Manager and User Control Panel) is installed, to the SRP-X700P through the USB terminal. Note that the USB terminal on the front panel has priority if the USB terminal on the front panel is being used. qh ANT IN terminal The antenna input terminal for the wireless tuner. Connect a UHF antenna of the AN-820A (option). 9V power is supplied from this terminal as the power for the antenna booster. Do not connect any antenna other than the AN820A, otherwise the system may not work or may cause failure. Note For details of installation and connection of an antenna, thoroughly read the operating instructions supplied with the antenna. If the antenna is not installed correctly, it may cause defective reception resulting in intermittent sound. Especially, if the location cannot be changed easily after installing the antenna, check the operations thoroughly prior to installation. Connect the antenna using coaxial cable having the impedance of 50 Ω. The maximum length of the cable is approximately 50 m with 5D-FB. Do not use the cable of a 75 Ω system such as 5C-2V, as its maximum length is half that of the 5D-FB and it may cause a trouble. If noise occurs: There can be a case that a specific channel cannot be used due to external noise or the noise caused by interference radio wave depending on the installation location. In such a case, find a channel that does not illuminate the RF indicator when the wireless microphone power and the transmitter power are turned off (i.e., the channel that is not adversely affected by noise and interference radio wave). Use the unaffected channel. Select the same unaffected channel for the wireless microphone and the transmitter. qj AC IN terminal Connect the power cord supplied to this terminal. qk + 48 V button Press this button to supply the DC +48V condenser microphone power to the MIC INPUT 1 to MIC INPUT 4 terminals. When this button is pressed ON ($), DC +48 V is output. By default, this button is set to OFF (4). ql MIC/LINE selector button You can select the input level of the MIC 5/LINE 1 IN and MIC 6/LINE 2 IN terminals with this button. (Refer to page 18.) Also, when this button is set to the (+48 V) MIC ($) position, the DC +48 V condenser microphone power is output automatically. By default, this button is set to LINE (4). Notes • The depressed position, which is the ON position, of both the qk +48 V button and the ql MIC/LINE selector button is lower than the face of the rear panel. The depressed ON position is designed intentionally to prevent mis-operation. • Before you make any attempt to disconnect and connect cables or to press any of the +48 V button, MIC/LINE selector button or other buttons, be sure to decrease the input fader completely or to turn off the power. w; CIRCUIT BREAKER The circuit breaker works to turn off the main power of this unit if an excessive current flows in the power supply of this unit. If the circuit breaker trips, please contact your local Sony Sales office or Dealer. 7