Sony SRXT420 User Manual (SRX-T420 user manual) - Page 62

PICTURE CONTROL, Window

Get Sony SRXT420 PDF manuals and user guides View all Sony SRXT420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Chapter 4 Adjustments and Settings Using the SRX Controller PICTURE CONTROL Window The PICTURE CONTROL window is used to select the input source or to adjust the picture quality. When "Quad-screen Mode" is selected with the INPUT SELECT radio buttons, the items can be independently adjusted for each input channel displayed on the screen. Board Shows the input board installed in the relative input board slot of the projector. Input Source Signal Mode: Click to open the drop-down list to select the type of signal input from equipment connected to the optional input board. When the LKRI-005 is installed Select the input signal type of progressive DVI-D signals. When used in normal, select "8bit Single Full," which is compatible with DVI1.0 standard and the signal level is Full Range compliance. When the DTV signal is input, select "8bit Single Limited," which is compatible with DVI1.0 standard and the signal level is Limited Range compliance. When the 10-bit signal based on Sony's unique specification is input, select "10bit Twin Full" or "10bit Single Full" for a signal of Full Range compliance, or "10bit Twin Limited" or "10bit Single Limited" for a signal of Limited Range compliance. When the LKRI-003 is installed For Single-link input, select "YPbPr" or "YPbPr FULL." For Dual-link input, select "RGB" or "RGB FULL." When "RGB" or "YPbPr" is selected, in the case that a 10-bit HD-SDI signal is input and "Contrast" is set to 90 in "Signal Adjust" of the PICTURE CONTROL window, mapping is done so that HD-SDI signal data values 1) of 64 to 960 are converted to the video levels of 0 to 100% to display an image on the projector. When "RGB FULL" or "YPbPr FULL" is selected, in the case that a 10-bit HD-SDI signal is input and "Contrast" is set to 90 in "Signal Adjust" of the PICTURE CONTROL window, mapping is done so that HD-SDI signal data values of 0 to 1023 are converted to the video levels of 0 to 100% to display an image on the projector. In this case, inhibition codes included in a 10-bit HD-SDI signal (data area 0 to 3, and 1020 to 1023) are blocked out. 1) Data value 64 of a 10-bit HD-SDI signal input is equivalent to the video level of 0% (black), and data value 960 equivalent to 100% (white). I/P Mode: Selects the I/P conversion mode. Depending on the input signal source, set the mode to "Interlace," "PsF" or "1080 50p60p." Notes • This item is available with the interlace, PsF or HD 50P/60P signal input. • When the LKRI-005 is installed, this item is not available. Signal Info (Information) Shows the horizontal and vertical frequencies of the input signal automatically. The values are approximate. The type of the input signal is also displayed. fH: Displays the horizontal frequency. fV: Displays the vertical frequency. Signal Adjust Adjusts the picture quality of the input signal. Clicking increases the setting value, and decreases it. Clicking the "RESET" button resets the following four settings to the factory preset values. Contrast: Adjusts the picture contrast. The higher the setting, the greater the contrast. Brightness: Adjusts the picture brightness. The higher the setting, the brighter the picture. 62 PICTURE CONTROL Window

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
62
PICTURE CONTROL Window
Chapter 4
Adjustments and Settings Using the SRX Controller
PICTURE CONTROL
Window
The PICTURE CONTROL window is used to select the
input source or to adjust the picture quality.
When “Quad-screen Mode” is selected with the INPUT
SELECT radio buttons, the items can be independently
adjusted for each input channel displayed on the screen.
Board
Shows the input board installed in the relative input board
slot of the projector.
Input Source
Signal Mode:
Click
to open the drop-down list to
select the type of signal input from equipment
connected to the optional input board.
When the LKRI-005 is installed
Select the input signal type of progressive DVI-D
signals.
When used in normal, select “8bit Single Full,” which
is compatible with DVI1.0 standard and the signal
level is Full Range compliance.
When the DTV signal is input, select “8bit Single
Limited,” which is compatible with DVI1.0 standard
and the signal level is Limited Range compliance.
When the 10-bit signal based on Sony’s unique
specification is input, select “10bit Twin Full” or
“10bit Single Full” for a signal of Full Range
compliance, or “10bit Twin Limited” or “10bit Single
Limited” for a signal of Limited Range compliance.
When the LKRI-003 is installed
For Single-link input, select “YPbPr” or “YPbPr
FULL.”
For Dual-link input, select “RGB” or “RGB FULL.”
When “RGB” or “YPbPr” is selected, in the case that
a 10-bit HD-SDI signal is input and “Contrast” is set
to 90 in “Signal Adjust” of the PICTURE CONTROL
window, mapping is done so that HD-SDI signal data
values
1)
of 64 to 960 are converted to the video levels
of 0 to 100% to display an image on the projector.
When “RGB FULL” or “YPbPr FULL” is selected, in
the case that a 10-bit HD-SDI signal is input and
“Contrast” is set to 90 in “Signal Adjust” of the
PICTURE CONTROL window, mapping is done so
that HD-SDI signal data values of 0 to 1023 are
converted to the video levels of 0 to 100% to display
an image on the projector. In this case, inhibition
codes included in a 10-bit HD-SDI signal (data area 0
to 3, and 1020 to 1023) are blocked out.
1)
Data value 64 of a 10-bit HD-SDI signal input is
equivalent to the video level of 0% (black), and data value
960 equivalent to 100% (white).
I/P Mode:
Selects the I/P conversion mode. Depending on
the input signal source, set the mode to “Interlace,”
“PsF” or “1080 50p60p.”
•
This item is available with the interlace, PsF or HD
50P/60P signal input.
•
When the LKRI-005 is installed, this item is not
available.
Signal Info (Information)
Shows the horizontal and vertical frequencies of the input
signal automatically. The values are approximate.
The type of the input signal is also displayed.
fH:
Displays the horizontal frequency.
fV:
Displays the vertical frequency.
Signal Adjust
Adjusts the picture quality of the input signal.
Clicking
increases the setting value, and
decreases it.
Clicking the “RESET” button resets the following four
settings to the factory preset values.
Contrast:
Adjusts the picture contrast. The higher the
setting, the greater the contrast.
Brightness:
Adjusts the picture brightness. The higher the
setting, the brighter the picture.
Notes