Sony STR DH100 Operating Instructions - Page 22

Tuning into a station, automatically Auto Tuning, Direct tuning, Using the controls on the, receiver - stereo audio receiver

Get Sony STR DH100 PDF manuals and user guides
UPC - 027242753570
View all Sony STR DH100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Tuning into a station automatically (Auto Tuning) 1 Press TUNER repeatedly to select the FM or AM band. 2 Press TUNING + or TUNING -. Press TUNING + to scan from low to high; press TUNING - to scan from high to low. The receiver stops scanning whenever a station is received. Using the controls on the receiver 1 Turn INPUT SELECTOR to select the FM or AM band. 2 Press TUNING MODE repeatedly to select "AUTO T.". 3 Press TUNING + or TUNING -. In case of poor FM stereo reception If the FM stereo reception is poor and "ST" flashes on the display, select monaural audio so that the sound will be less distorted. Press FM MODE repeatedly until the "MONO" indicator lights up on the display. To return to stereo mode, press FM MODE repeatedly until the "MONO" indicator on the display does not light up. Tuning into a station directly (Direct tuning) You can enter the frequency of a station directly by using the numeric buttons. 1 Press TUNER repeatedly to select the FM or AM band. You can also use INPUT SELECTOR on the receiver. 2 Press D.TUNING. 3 Press the numeric buttons to enter the frequency. Example 1: FM 102.50 MHz Select 1 b 0 b 2 b 5 b 0 Example 2: AM 1,350 kHz Select 1 b 3 b 5 b 0 4 Press ENTER. You can also use MEMORY/ENTER on the receiver. Tip If you have tuned in an AM station, adjust the direction of the AM loop antenna (aerial) for optimum reception. If you cannot tune in a station Make sure you have entered the right frequency. If not, repeat steps 2 to 4. If you still cannot tune in a station, the frequency is not used in your area. 22GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
22
GB
1
Press TUNER repeatedly to
select the FM or AM band.
2
Press TUNING + or TUNING –.
Press TUNING + to scan from low to
high; press TUNING – to scan from high
to low.
The receiver stops scanning whenever a
station is received.
Using the controls on the
receiver
1
Turn INPUT SELECTOR to select the FM
or AM band.
2
Press TUNING MODE repeatedly to select
“AUTO T.”.
3
Press TUNING + or TUNING –.
In case of poor FM stereo
reception
If the FM stereo reception is poor and “ST”
flashes on the display, select monaural audio
so that the sound will be less distorted.
Press FM MODE repeatedly until the
“MONO” indicator lights up on the display.
To return to stereo mode, press FM MODE
repeatedly until the “MONO” indicator on the
display does not light up.
You can enter the frequency of a station
directly by using the numeric buttons.
1
Press TUNER repeatedly to
select the FM or AM band.
You can also use INPUT SELECTOR on
the receiver.
2
Press D.TUNING.
3
Press the numeric buttons to
enter the frequency.
Example 1: FM 102.50 MHz
Select 1
b
0
b
2
b
5
b
0
Example 2: AM 1,350 kHz
Select 1
b
3
b
5
b
0
4
Press ENTER.
You can also use MEMORY/ENTER on
the receiver.
Tip
If you have tuned in an AM station, adjust the
direction of the AM loop antenna (aerial) for
optimum reception.
If you cannot tune in a station
Make sure you have entered the right
frequency. If not, repeat steps 2 to 4. If you
still cannot tune in a station, the frequency is
not used in your area.
Tuning into a station
automatically (Auto Tuning)
Tuning into a station directly
(Direct tuning)