Sony VPL FX40 Operating Instructions - Page 47

Messages List, Warning Messages, Caution Messages

Get Sony VPL FX40 - XGA LCD Projector PDF manuals and user guides
UPC - 027242693524
View all Sony VPL FX40 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Messages List Warning Messages Use the list below to check the meaning of the messages displayed on the screen. Message Meaning and Remedy High temp.! Lamp off in 1 The internal temperature is too high. min. c Turn off the power. c Check to see that nothing is blocking the ventilation holes. Frequency is out of range! • This input signal cannot be projected as the frequency is out of the acceptable range of the projector. • The resolution setting of the output signal of the computer is too high. c Input a signal that is within the range of the frequency. Please check Input-C Signal Sel. You have input an RGB signal from the computer when "Input-C Signal Sel." in the Setup menu is set to "Component." c Set "Input-C Signal Sel." correctly (see page 34). Please replace the Lamp and clean the Filter. • It is time to replace the lamp and clean the air filter. c Replace the lamp (see page 41) and clean the filter (see page 43). • If this message appears again after you replace the lamp, the lamp replacement process is not complete. c Perform the operations in step 8 to 11 on page 42. Note To erase a message, press any key on the control panel of the projector or on the remote commander. The projector temperature is high. "High Altitude Mode" should be "On" if the projector is being used at high altitude. c Check to ensure that the ventilation holes on the projector are not covered (see page 11). c When using the projector at high altitude, set the "High Altitude Mode" to "On". Note If the temperature inside the projector remains high, the "High Altitude Mode" is switched to "On" in one minute, then the fan speed increases. Caution Messages Use the list below to check the meaning of the messages displayed on the screen. Message Meaning and Remedy Not applicable! You have pressed the wrong key. c Press the appropriate key. The panel keys are locked! "Panel Key Lock" in the Function menu is set to "On." c All the keys on the control panel of the projector are locked. Operate the projector with the keys on the Remote Commander (see page 36). Others Troubleshooting 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
47
Troubleshooting
Others
Warning Messages
Use the list below to check the meaning of the messages displayed on the screen.
Caution Messages
Use the list below to check the meaning of the messages displayed on the screen.
Messages List
Message
Meaning and Remedy
High temp.! Lamp off in 1
min.
The internal temperature is too high.
c
Turn off the power.
c
Check to see that nothing is blocking the ventilation holes.
Frequency is out of range!
•
This input signal cannot be projected as the frequency is out of the
acceptable range of the projector.
• The resolution setting of the output signal of the computer is too
high.
c
Input a signal that is within the range of the frequency.
Please check Input-C
Signal Sel.
You have input an RGB signal from the computer when “Input-C
Signal Sel.” in the Setup menu is set to “Component.”
c
Set “Input-C Signal Sel.” correctly (see page 34).
Please replace the Lamp
and clean the Filter.
• It is time to replace the lamp and clean the air filter.
c
Replace the lamp
(see page 41) and clean the filter (see
page 43).
• If this message appears again after you replace the lamp, the lamp
replacement process is not complete.
c
Perform the operations in step 8 to 11 on page 42.
To erase a message, press any key on the control panel of the
projector or on the remote commander.
The projector temperature
is high. “High Altitude
Mode” should be “On” if
the projector is being used
at high altitude.
c
Check to ensure that the ventilation holes on the projector are not
covered (see page 11).
c
When using the projector at high altitude, set the “High Altitude
Mode” to “On”.
If the temperature inside the projector remains high, the “High
Altitude Mode” is switched to “On” in one minute, then the fan
speed increases.
Message
Meaning and Remedy
Not applicable!
You have pressed the wrong key.
c
Press the appropriate key.
The panel keys are locked!
“Panel Key Lock” in the Function menu is set to “On.”
c
All the keys on the control panel of the projector are locked.
Operate the projector with the keys on the Remote Commander
(see page 36).
Note
Note