Stihl FS 55 R Product Instruction Manual - Page 24

STIHL AutoCut C 25-2 - gearbox

Get Stihl FS 55 R PDF manuals and user guides View all Stihl FS 55 R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

English N Go to "Mounting the mowing head" or "Mounting the metal cutting attachment". If the parts are mounted to the gearbox N Go to "Removing the mounting hardware". Removing the mounting hardware N Go to "Mounting the mowing head" or "Mounting the metal cutting attachment". Blocking the output shaft 2 STIHL TrimCut 31-2, STIHL FixCut 25-2, STIHL PolyCut 20-3 002BA166 KN 002BA081 KN N Block the shaft - see next chapter on "Blocking the output shaft". N Use the combination wrench (6) - comes standard with machine or is available as special accessory - to unscrew the nut (3) clockwise (lefthand thread) from the shaft (2). N Pull the thrust washer (5) off the shaft (2). The rider plate (4) is in the parts kit supplied with the machine. 8 7 7 N Insert the stop pin (7) or screwdriver - come standard with machine or are available as special accessories - in the hole (8) in the gearbox as far as stop, and apply slight pressure. N Rotate the nut or cutting attachment on the shaft (2) until the stop pin slips into position and blocks the shaft. Attaching the mowing head Keep the information sheet for the mowing head in a safe place. STIHL SuperCut 20-2, STIHL AutoCut 25-2, STIHL AutoCut C 25-2, 1 N Turn the mowing head counterclockwise until it is flush against the shaft (1) N Block the shaft N Tighten the mowing head Remove the tool used to block the shaft. Removing the mowing head N Block the shaft STIHL SuperCut 20-2, STIHL AutoCut 25-2, STIHL AutoCut C 25-2, 22 FS 55, FS 55 C, FS 55 R, FS 55 RC

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
FS 55, FS 55 C, FS 55 R, FS 55 RC
English
22
N
Go to "Mounting the mowing head"
or "Mounting the metal cutting
attachment".
If the parts are mounted to the
gearbox
N
Go to "Removing the mounting
hardware".
Removing the mounting hardware
N
Block the shaft – see next chapter
on "Blocking the output shaft".
N
Use the combination wrench (6) –
comes standard with machine or is
available as special accessory – to
unscrew the nut (3) clockwise (left-
hand thread) from the shaft (2).
N
Pull the thrust washer (5) off the
shaft (2).
The rider plate (4) is in the parts kit
supplied with the machine.
N
Go to "Mounting the mowing head"
or "Mounting the metal cutting
attachment".
Blocking the output shaft
N
Insert the stop pin
(7) or screwdriver
– come standard with machine or
are available as special accessories
– in the hole (8) in the gearbox as
far as stop, and apply slight
pressure.
N
Rotate the nut or cutting attachment
on the shaft (2) until the stop pin
slips into position and blocks the
shaft.
Attaching the mowing head
Keep the information sheet for the
mowing head in a safe place.
STIHL SuperCut 20-2,
STIHL AutoCut 25-2,
STIHL AutoCut C 25-2,
STIHL TrimCut 31-2,
STIHL FixCut 25-2,
STIHL PolyCut 20-3
N
Turn the mowing head
counterclockwise until it is flush
against the shaft (1)
N
Block the shaft
N
Tighten the mowing head
Removing the mowing head
N
Block the shaft
STIHL SuperCut 20-2,
STIHL AutoCut 25-2,
STIHL AutoCut C 25-2,
7
8
2
002BA166 KN
7
Remove the tool used to block the
shaft.
1
002BA081 KN