Stihl HL 100 K 0 Product Instruction Manual - Page 11

Operating instructions, Warning, Warning, Danger

Get Stihl HL 100 K 0 PDF manuals and user guides View all Stihl HL 100 K 0 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

English / USA Operating instructions !Warning! Do not operate your power tool using the starting throttle lock, as you do not have control of the engine speed. In the event of an emergency, switch off the engine immediately - move the slide control / stop switch to 0 or STOP. !Warning The cutter blades continue to move for a short period after the throttle trigger is released (flywheel effect). Accelerating the engine while the blades are blocked increases the load and will cause the clutch to slip continuously. This may result in overheating and damage to important components (e.g. clutch, polymer housing components) - which can then increase the risk of injury from the blades moving while the engine is idling. !Warning! On units with an adjustable cutter bar: To reduce the risk of injury, never touch the blades while making adjustments. The power tool has a large range. 15m (50ft) In order to reduce the risk of personal or even fatal injury to bystanders from falling objects or inadvertent contact with the moving cutter blades of your power tool always keep bystanders at least 50 feet (15m) away when the power tool is running. Stop the engine and cutting tool immediately if you are approached. !Warning! Before you start work, examine the hedge area for stones, fence wire, metal or other solid objects which could damage the cutter blades. Take particular care when cutting hedges next to or against wire fences. Do not touch the wire with the cutting blades. When working close to the ground, make sure that no sand, grit or stones get between the cutter blades. Striking solid foreign objects such as stones, fence wire or metal could damage the cutting attachment and may cause blades to crack, chip or break. STIHL does not recommend the use of your power tool when cutting in areas where the blades could contact such objects. !Warning Observe the cutting blades at all times - do not cut any areas of the hedge that you cannot see. When cutting the top of a taller hedge, check the other side of the hedge frequently for bystanders, animals and obstructions. Danger! Your power tool is not insulated against electric shock. To reduce the risk of electrocution, never operate this power tool in the vicinity of any wires or cables (power, etc.) which may be carrying electric current. !Warning! If the cutting tool becomes clogged or stuck, always turn off the engine and make sure the cutting tool has stopped before cleaning. Grass, weeds, etc. should be cleaned off the cutting tool at regular intervals. 10 HL 100

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
10
English / USA
HL 100
Operating instructions
!
Warning!
Do not operate your power tool using the
starting throttle lock, as you do not have
control of the engine speed.
In the event of an emergency, switch off
the engine immediately – move the slide
control / stop switch to
0
or
STOP
.
!
Warning
The cutter blades continue to move for a
short period after the throttle trigger is
released (flywheel effect).
Accelerating the engine while the blades
are blocked increases the load and will
cause the clutch to slip continuously.
This may result in overheating and
damage to important components (e.g.
clutch, polymer housing components) –
which can then increase the risk of injury
from the blades moving while the engine
is idling.
!
Warning!
On units with an adjustable cutter bar: To
reduce the risk of injury, never touch the
blades while making adjustments.
The power tool
has a large range.
In order to reduce
the risk of personal
or even fatal injury
to bystanders from
falling objects or inadvertent contact with
the moving cutter blades of your power
tool always keep bystanders at least 50
feet (15m) away when the power tool is
running.
Stop the engine and cutting tool
immediately if you are approached.
!
Warning!
Before you start work, examine the
hedge area for stones, fence wire, metal
or other solid objects which could
damage the cutter blades.
Take particular care when cutting
hedges next to or against wire fences.
Do not touch the wire with the cutting
blades. When working close to the
ground, make sure that no sand, grit or
stones get between the cutter blades.
Striking solid foreign objects such as
stones, fence wire or metal could
damage the cutting attachment and may
cause blades to crack, chip or break.
STIHL does not recommend the use of
your power tool when cutting in areas
where the blades could contact such
objects.
!
Warning
Observe the cutting blades at all times –
do not cut any areas of the hedge that
you cannot see. When cutting the top of
a taller hedge, check the other side of
the hedge frequently for bystanders,
animals and obstructions.
Danger!
Your power tool is not
insulated against electric
shock. To reduce the risk
of electrocution, never
operate this power tool in the vicinity of
any wires or cables (power, etc.) which
may be carrying electric current.
!
Warning!
If the cutting tool becomes clogged or
stuck, always turn off the engine and
make sure the cutting tool has stopped
before cleaning. Grass, weeds, etc.
should be cleaned off the cutting tool at
regular intervals.
15m (50ft)