Stihl HL 100 K 0 Product Instruction Manual - Page 21

Adjusting Cutter Bar

Get Stihl HL 100 K 0 PDF manuals and user guides View all Stihl HL 100 K 0 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

English / USA Adjusting Cutter Bar 0° to 90° Version On this version the angle of the cutter bar can be adjusted in 8 stages between 0° (straight) and 90° (upwards at right angle. There are therefore 9 possible working positions. Carry out the adjustment only when the cutting blades are at a standstill - engine at idle speed - not in the starting throttle position. 0° to 135° Version On this version the angle of the cutter bar can be adjusted upwards in 4 stages from 0° (straight) to 45°, and downwards in 8 stages from 0° to 90° (right angle facing down). There are therefore 13 possible working positions. There is also a special transport position. The gearbox becomes hot during operation. To reduce the risk of burn injury, do not touch the gear housing. To avoid risk of injury, never touch the blades while making adjustments. : Pull back the sliding sleeve (1) and use the lever (2) to adjust the joint by one or several holes. : Release the sliding sleeve and make sure the pin engages the quadrant (3). The sliding sleeve butts against the housing when the pin is properly engaged (after making adjustment). 20 HL 100

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
20
English / USA
HL 100
0° to 90° Version
On this version the angle of the cutter
bar can be adjusted in 8 stages between
0° (straight) and 90° (upwards at right
angle. There are therefore 9 possible
working positions.
Carry out the adjustment only when
the cutting blades are at a standstill
– engine at idle speed – not in the
starting throttle position.
The gearbox becomes hot during
operation. To reduce the risk of burn
injury, do not touch the gear
housing.
To avoid
risk of injury
, never touch
the blades while making
adjustments.
:
Pull back the sliding sleeve (
1
) and
use the lever (
2
) to adjust the joint
by one or several holes.
:
Release the sliding sleeve and
make sure the pin engages the
quadrant (
3
).
The sliding sleeve butts against the
housing when the pin is properly
engaged (after making adjustment).
0° to 135° Version
On this version the angle of the cutter
bar can be adjusted upwards in 4 stages
from 0° (straight) to 45°, and downwards
in 8 stages from 0° to 90° (right angle
facing down). There are therefore 13
possible working positions.
There is also a special transport
position.
Adjusting Cutter Bar