Stihl MS 290 STIHL FARM BOSS Product Instruction Manual - Page 45

Replacing Starter Rope, and Rewind Spring - starter pawl and rope

Page 45 highlights

133BA014 KN English / USA If engine is down on power, difficult to start or runs poorly at idling speed, first check the spark plug. : Remove spark plug - see "Starting / Stopping the Engine". : Clean dirty spark plug. : Check electrode gap (A) and readjust if necessary - see "Specifications". : Use only resistor type spark plugs of the approved range. Rectify problems which have caused fouling of spark plug: : Too much oil in fuel mix. : Dirty air filter. : Unfavorable running conditions, e.g. operating at part load. Fit a new spark plug after approx. 100 operating hours or earlier if the electrodes are badly eroded. Replacing Starter Rope and Rewind Spring 1 1 1 1 : Remove the screws (1). : Ease fan housing away from 1 crankcase and remove it sideways. 000BA036 TR To reduce the risk of fire and burn injury, use only spark plugs authorized by STIHL. Always press spark plug boot (2) snugly onto spark plug terminal (1) of the proper size. (Note: If terminal has detachable SAE adapter nut, it must be attached.) A loose connection between spark plug boot and ignition wire connector in the boot may create arcing that could ignite combustible fumes and cause a fire. 23 4 : Use screwdriver or suitable pliers to carefully remove spring clip (2) from the starter post. : Carefully remove the rope rotor with washer (3) and pawl (4). The rewind spring may pop out and uncoil during this operation. 133BA015 KN 44 MS 290, MS 310, MS 390

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126

44
English / USA
MS 290, MS 310, MS 390
If engine is down on power, difficult to
start or runs poorly at idling speed, first
check the spark plug.
:
Remove spark plug – see "Starting /
Stopping the Engine".
:
Clean dirty spark plug.
:
Check electrode gap (
A
) and
readjust if necessary – see
"Specifications".
:
Use only resistor type spark plugs
of the approved range.
Rectify problems which have caused
fouling of spark plug:
:
Too much oil in fuel mix.
:
Dirty air filter.
:
Unfavorable running conditions,
e.g. operating at part load.
Fit a new spark plug after approx.
100 operating hours
or earlier if the electrodes are badly
eroded.
To reduce the risk of fire and burn
injury, use only spark plugs
authorized by STIHL. Always press
spark plug boot (
2
)
snugly onto
spark plug terminal (
1
) of the proper
size. (Note: If terminal has
detachable SAE adapter nut, it must
be attached.)
A loose connection between spark
plug boot and ignition wire
connector in the boot may create
arcing that could ignite combustible
fumes and cause a fire.
:
Remove the screws
(1)
.
:
Ease fan housing away from
crankcase and remove it sideways.
:
Use screwdriver or suitable pliers to
carefully remove spring clip
(2)
from
the starter post.
:
Carefully remove the rope rotor with
washer
(3)
and pawl
(4)
.
The rewind spring may pop out and
uncoil during this operation.
000BA036 TR
1
Replacing Starter Rope
and Rewind Spring
1
1
1
1
133BA014 KN
2
3
4
133BA015 KN