Stihl MSE 200 Product Instruction Manual - Page 34

Operating Instructions

Get Stihl MSE 200 PDF manuals and user guides View all Stihl MSE 200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

English / USA Operating Instructions MSE 140 C, MSE 160 C, MSE 180 C 1 : Wait for the overload circuit breaker to cool down. : Press in button (1) as far as stop. If the motor does not start when you switch on, you can assume that the overload circuit breaker has not cooled down sufficiently. Wait a little longer and then press the button again as far as stop. Once the motor starts: : Run your saw for about 15 seconds off-load. This helps cool the motor windings and prevents the overload circuit breaker tripping again. 100BA029 KN 100BA030 KN MSE 200 C 1 Model MSE 200 C is equipped with an electronic overload circuit breaker which measures motor temperature and current drawn. : The LED indicator (1) comes on in case of overload and the power supply is interrupted. The indicator goes off after about 2 seconds and the saw is ready for operation. : Run your saw for about 15 seconds off-load. This helps cool the motor windings. Note that the overload indicator glows only as long as the trigger switch is activated. During operation : Check level in chain oil tank. : Fill up with fresh chain oil when the level reaches the "min" mark - see "Filling Chain Oil Tank". : Start cutting with the saw chain running. : Always cut with a properly sharpened chain and apply only moderate feed pressure. The sound and running behavior of the saw must remain constant. The motor speed may only drop a little in the cut - the chain must not jerk or stop. : If motor noise drops suddenly or the chain stops, reduce feed pressure immediately to avoid overheating and possible damage to the saw. MSE 140 C, MSE 160 C, MSE 180 C, MSE 200 C 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
33
MSE 140 C, MSE 160 C, MSE 180 C, MSE 200 C
English / USA
MSE 140 C, MSE 160 C,
MSE 180 C
:
Wait for the overload circuit breaker
to cool down.
:
Press in button
(1)
as far as stop. If
the motor does not start when you
switch on, you can assume that the
overload circuit breaker has not
cooled down sufficiently. Wait a little
longer and then press the button
again as far as stop.
Once the motor starts:
:
Run your saw for about 15 seconds
off-load. This helps cool the motor
windings and prevents the overload
circuit breaker tripping again.
MSE 200 C
Model MSE 200 C is equipped with an
electronic overload circuit breaker which
measures motor temperature and
current drawn.
:
The LED indicator
(1)
comes on in
case of overload and the power
supply is interrupted. The indicator
goes off after about 2 seconds and
the saw is ready for operation.
:
Run your saw for about 15 seconds
off-load. This helps cool the motor
windings.
Note that the overload indicator glows
only as long as the trigger switch is
activated.
During operation
:
Check level in chain oil tank.
:
Fill up with fresh chain oil when the
level reaches the "min" mark - see
"Filling Chain Oil Tank".
:
Start cutting with the saw chain
running.
:
Always cut with a properly
sharpened chain and apply only
moderate feed pressure
. The
sound and running behavior of the
saw must remain constant. The
motor speed may only drop a little in
the cut –
the chain must not jerk
or stop
.
:
If motor noise drops suddenly or the
chain stops, reduce feed pressure
immediately
to avoid overheating
and possible damage to the saw.
100BA029 KN
1
100BA030 KN
1
Operating Instructions