TP-Link TL-WA830RE TL-WA830RE V1 User Guide - Page 44

Wireless Statistics, 4.6 DHCP - ip

Get TP-Link TL-WA830RE PDF manuals and user guides View all TP-Link TL-WA830RE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

TL-WA830RE 300Mbps Wireless N Range Extender User Guide ¾ Run Time - How long this function is running. ¾ Transmit - Wireless transmit rate information. ¾ Receive - Wireless receive rate information. Click the Start button to start wireless throughput monitor. Click the Stop button to stop wireless throughput monitor. 4.5.6 Wireless Statistics Selecting Wireless > Wireless Statistics will allow you to see the wireless transmission information in the following screen shown in Figure 4-20. Figure 4-20 Statistics of the device attached wireless stations ¾ Operation Mode - Shows the current operation mode ¾ MAC Address - Shows the connected wireless station's MAC address ¾ Current Status - The connected wireless station's running status, one of STA-AUTH / STA-ASSOC / STA-JOINED / WPA / WPA-PSK / WPA2 / WPA2-PSK / AP-UP / AP-DOWN / Disconnected ¾ Received Packets - packets received by the station ¾ Sent Packets - packets sent by the station You cannot change any of the values on this page. To update this page and to show the current connected wireless stations, click the Refresh button. If the numbers of connected wireless stations go beyond one page, click the Next button to go to the next page and click the Previous button to return the previous page. ) Note: This page will be refreshed automatically every 5 seconds. 4.6 DHCP DHCP stands for Dynamic Host Configuration Protocol. The DHCP Server will automatically assign dynamic IP addresses to the computers on the network. This protocol simplifies network management and allows new wireless devices to receive IP addresses automatically without the 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
TL-WA830RE
300Mbps Wireless N Range Extender User Guide
¾
Run Time -
How long this function is running.
¾
Transmit -
Wireless transmit rate information.
¾
Receive -
Wireless receive rate information.
Click the
Start
button to start wireless throughput monitor.
Click the
Stop
button to stop wireless throughput monitor.
4.5.6 Wireless Statistics
Selecting
Wireless
>
Wireless Statistics
will allow you to see the wireless transmission
information in the following screen shown in Figure 4-20.
Figure 4-20 Statistics of the device attached wireless stations
¾
Operation Mode -
Shows the current operation mode
¾
MAC Address -
Shows the connected wireless station's MAC address
¾
Current Status -
The connected wireless station's running status, one of STA-AUTH /
STA-ASSOC / STA-JOINED / WPA / WPA-PSK / WPA2 / WPA2-PSK / AP-UP / AP-DOWN /
Disconnected
¾
Received Packets -
packets received by the station
¾
Sent Packets -
packets sent by the station
You cannot change any of the values on this page. To update this page and to show the current
connected wireless stations, click the
Refresh
button.
If the numbers of connected wireless stations go beyond one page, click the
Next
button to go to
the next page and click the
Previous
button to return the previous page.
)
Note:
This page will be refreshed automatically every 5 seconds.
4.6
DHCP
DHCP stands for Dynamic Host Configuration Protocol. The DHCP Server will automatically
assign dynamic IP addresses to the computers on the network. This protocol simplifies network
management and allows new wireless devices to receive IP addresses automatically without the
36