TRENDnet 12dBi User's Guide - Page 23

Wireless MAC Filter Setup, MAC or Only Allow List MAC

Get TRENDnet 12dBi PDF manuals and user guides View all TRENDnet 12dBi manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

TRENDnet User's Guide • Session Timeout : The Session timeout is in the range of 0~60 seconds. The default is 0 to disable re-authenticate service. • Amount of time before a client will be required to re-authenticate.  WEP 802.1X : When WEP 802.1x Authentication is enabled, please refer to the following Dynamic WEP and RADIUS settings to complete configuration. TEW-676APBO Wireless MAC Filter Setup Continue Virtual AP Setup section. For each Virtual AP setting, the administrator can allow or reject clients to access each Virtual AP.  Radius Server Settings : • IP Address : Enter the IP address of the Authentication RADIUS server. • Port : By default, it's 1812. The port number used to communicate with RADIUS server. • Shared secret : A secret key used between system and RADIUS server. Supports 8 to 64 characters. • Session Timeout : The Session timeout is in the range of 0~60 seconds. The default is 0 to disable re-authenticate service. • Amount of time before a client will be required to re-authenticate. Click Save button to save your changes. Click Reboot button to activate your changes  MAC Filter Setup : By default, it's "Disable". Options are Disable, Only Deny List MAC or Only Allow List MAC. Two ways to set MAC filter rules :  Only Allow List MAC. The wireless clients in the "Enable" list will be allowed to access the Access Point; All others or clients in the "Disable" list will be denied.  Only Deny List MAC. The wireless clients in the "Enable" list will be denied to access the Access Point; All others or clients in the "Disable" list will be allowed. Add a station MAC : Enter MAC address (e.g. aa:bb:cc:00:00:0a) and click "Add" button, then the MAC address should display in the "Enable" List. There are a maximum of 20 clients allowed in this "Enable" List. The MAC addresses of the wireless clients can be added and removed to the list using the Add and Remove buttons. Click Reboot button to activate your changes © Copyright 2012TRENDnet. All Rights Reserved. 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
© Copyright 2012TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-676APBO
23
•
Session Timeout :
The Session timeout is in the range of
0
~
60
seconds
. The
default is
0
to
disable re-authenticate service.
•
Amount of time before a client will be required to re-authenticate.
WEP 802.1X :
When WEP 802.1x Authentication is enabled, please refer to the
following Dynamic WEP and RADIUS settings to complete configuration.
Radius Server Settings :
•
IP Address :
Enter the IP address of the Authentication RADIUS server.
•
Port :
By default, it’s
1812
.
The port number used to communicate with RADIUS
server.
•
Shared secret :
A secret key used between system and RADIUS server. Supports
8
to
64
characters.
•
Session Timeout :
The Session timeout is in the range of
0
~
60
seconds
. The
default is
0
to
disable re-authenticate service.
•
Amount of time before a client will be required to re-authenticate.
Click
Save
button to save your changes. Click
Reboot
button to activate your changes
Wireless MAC Filter Setup
Continue
Virtual
AP
Setup
section. For each Virtual AP setting, the administrator can
allow or reject clients to access each Virtual AP.
MAC Filter Setup :
By default, it’s “
Disable
”. Options
are
Disable, Only Deny List
MAC or Only Allow List MAC
.
Two ways to set MAC filter rules :
Only
Allow List MAC
.
The wireless clients in the “
Enable
” list will be
allowed
to access the Access Point;
All others or clients in the “
Disable
” list will be
denied
.
Only
Deny List MAC
.
The wireless clients in the “
Enable
” list will be
denied
to access the Access Point; All
others or clients
in the “
Disable
” list will be
allowed
.
Add a station MAC :
Enter MAC address (e.g. aa:bb:cc:00:00:0a) and click “
Add
” button,
then the MAC address should display in the “
Enable
” List.
There are a maximum of
20
clients allowed in this “Enable” List. The MAC addresses of
the wireless clients can be added and removed to the list using the
Add
and
Remove
buttons
.
Click
Reboot
button to activate your changes