Toshiba MW30G71 Service Manual - Page 51
Table 1-10, After the data input, set to the initializing of shipping., C4-10, FIG. 1
View all Toshiba MW30G71 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 51 highlights
WHEN REPLACING EEPROM (MEMORY) IC INI 1F00 1F10 1F20 1F30 1F40 1F50 1F60 1F70 1F80 1F90 1FA0 1FB0 1FC0 1FD0 1FE0 1FF0 2000 2010 2020 2030 2040 +0 +1 +2 00 FF FF 5C 00 3B 01 B1 03 00 BF 07 E0 01 29 01 FF FF 5C 00 3B 01 B1 03 00 BF 07 E0 01 29 01 FF FF 5C 00 3B 01 B1 03 00 BF 07 E0 01 29 01 FF FF 58 00 37 01 B1 03 00 D5 05 E0 01 29 01 ... ... +3 +4 FF FF 03 59 69 00 00 00 03 60 FF FF 03 3E 69 00 00 00 03 60 FF FF 03 1D 69 00 55 80 03 60 FF FF 03 1D 69 00 77 80 03 7A ... ... +5 +6 +7 +8 +9 +A +B +C +D +E +F FF FF FF FF FF FF FF FF FF FF FF 00 05 02 A8 58 01 58 05 DF 02 E0 03 00 00 61 FE 05 F5 00 00 08 3F 00 C0 03 C0 03 00 00 EF 02 EF 02 00 95 00 1C 00 1C 00 54 00 54 00 FF FF FF FF FF FF FF FF FF FF FF 00 05 02 A8 58 01 22 06 DF 02 E0 03 00 00 61 FE 05 F5 00 00 08 3F 00 C0 03 C0 03 00 00 EF 02 EF 02 00 95 00 1C 00 1C 00 54 00 54 00 FF FF FF FF FF FF FF FF FF FF FF 00 05 02 A8 58 01 1C 07 DF 02 E0 03 00 00 61 FE 05 F5 00 00 08 3F 80 C0 03 C0 03 00 00 EF 02 EF 02 00 95 00 1C 00 1C 00 54 00 54 00 FF FF FF FF FF FF FF FF FF FF FF 00 05 02 A8 58 01 1C 07 DF 02 E0 03 01 43 82 FE 05 00 08 12 07 D7 80 DD 02 DD 02 00 00 EF 02 EF 02 00 35 04 1C 00 1C 00 F3 03 F3 03 Table 1-10 ADDRESS DATA 1. Turn on the POWER, and set to the TV mode. 2. Enter DATA SET mode by setting VOLUME to minimum. 3. Press both VOL. DOWN button on the set and Channel button (6) on the remote control OEC7121A_054 for more than 2 seconds. ADDRESS and DATA should appear as FIG 1. INIT 0000 FF 4. ADDRESS is now selected and should "blink". Using the UP/DOWN button on the remote, step through the ADDRESS until required ADDRESS to be changed is reached. CRT ON 0010 5. Press RIGHT/LEFT button to select DATA. When DATA is selected, it will "blink". 6. Again, step through the DATA using UP/DOWN button until required DATA value has been selected. 7. Pressing RIGHT/LEFT button will take you back to ADDRESS for further selection if necessary. FIG. 1 8. Repeat steps 4 to 7 until all data has been checked. 9. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input. After the data input, set to the initializing of shipping. 10. Turn on the POWER, and set to the TV mode. 11. Press both VOL. DOWN button on the set and Channel button (1) on the remote control for more than 2 seconds. 12. After the finishing of the initializing of shipping, the unit will turn off automatically. The unit will now have the correct DATA for the new MEMORY IC. C4-10