Toshiba SD-V593 User Manual - Page 25

Setting the video channel

Get Toshiba SD-V593 PDF manuals and user guides View all Toshiba SD-V593 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Basic setup Basic setup Setting the video channel When a TV is connected with the 75 ohm coaxial cable only. To view playback of a recorded tape or DVD disc, or to watch a program selected by the VCR's channel selector, the TV must be set to channel 3 or 4 (video channel). POWER DVD/VCR 3 4 Setting the video channel 1 Press DVD/VCR to operate the DVD/VCR. 2 Press and hold 3 or 4 on the remote for 3 seconds in standby mode. The video channel will OR start to flash for 3 seconds in the display window. TV/VCR DVD/VCR SELECT For a push-button TV tuner If CH 3 or 4 corresponding to the video channel cannot be tuned on your TV, proceed as follows: set the VCR 3/4 channel selector and the TV to CH 3 or 4, play back a prerecorded tape and tune the TV to receive a sharp color picture from the video cassette recorder. Refer to your TV owner's manual for details. Note: If the unit does not operate properly, or No key operation (by the unit and/or the remote control): Static electricity, etc., may affect the player's operation. Disconnect the AC power cord once, then connect it again. 3 Press POWER to turn on the DVD/VCR. 4 Press DVD/VCR SELECT selector to select the VCR mode. The VCR indicator on the front panel will light. 5 Turn ON the TV and set to CH 3 or 4 to correspond with the channel selected in step 2. 6 Press TV/VCR to select the VCR position. The VCR indicator will appear in the display window. 7 Select any channel to receive a TV station in your area. The channel number will appear on the screen for about 4 seconds. 2F90201A (E)p16-28 25 4/4/05, 9:02 PM 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
25
Basic setup
Setting the video channel
When a TV is connected with the 75 ohm coaxial cable only.
To view playback of a recorded tape or DVD disc, or to watch a
program selected by the VCR's channel selector, the TV must be set to
channel 3 or 4 (video channel).
Setting the video channel
Press POWER to turn on the DVD/VCR.
Press DVD/VCR SELECT selector to select the
VCR mode.
Turn ON the TV and set to CH 3 or 4 to corre-
spond with the channel selected in step 2.
Press TV/VCR to select the VCR position.
Select any channel to receive a TV station in your area.
The channel number will appear on the screen for
about 4 seconds.
2
The VCR indicator on the
front panel will light.
3
4
5
6
7
The VCR indicator will
appear in the display
window.
For a push-button TV tuner
If CH 3 or 4 corresponding to the video channel cannot
be tuned on your TV, proceed as follows: set the VCR
3/4 channel selector and the TV to CH 3 or 4, play
back a prerecorded tape and tune the TV to receive a
sharp color picture from the video cassette recorder.
Refer to your TV owner's manual for details.
Note:
If the unit does not operate properly, or No key operation
(by the unit and/or the remote control):
Static electricity, etc.,
may affect the player's operation. Disconnect the AC power cord
once, then connect it again.
POWER
DVD/VCR SELECT
DVD/VCR
Press and hold 3 or 4 on the remote for 3
seconds in standby mode.
The video channel will
start to flash for 3
seconds in the display
window.
3
4
OR
1
Press DVD/VCR to operate the DVD/VCR.
TV/VCR
Basic setup
2F90201A (E)p16-28
4/4/05, 9:02 PM
25