Tripp Lite SU1500XLCD Owner's Manual for On-Line Tower LCD UPS 933168 - Page 24

If VIEW IP ADDRESS is attempted for IPv6 level IP

Get Tripp Lite SU1500XLCD PDF manuals and user guides View all Tripp Lite SU1500XLCD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Operation 8 The EXTERNAL BATTERY TYPE selection screen will appear. EXTERNAL BATTERY TYPE refers to the ability for the UPS to become aware of which external battery pack is connected to the UPS. Setting the external battery configuration enhances the accuracy of the MINUTES RUNTIME countdown during power failure conditions. The LCD interface supports no external batteries with the factory configuration of BP0. Two additonal LCD configurable external battery pack options are available under the user selection of BP0, BP1 & BP2. See the table to determine whether BP1 or BP2 applies to your external battery pack. If your battery pack is not listed or you are using more than one of any supported external battery pack, you must use Tripp Lite's EXTERNAL BATTERY CONFIGURATION TOOL software available for download at this link: http://www.tripplite.com/bpconfig NOTE: Use the BP0 setting if you plan to use the EXTERNAL BATTERY CONFIGURATION TOOL software. After the software configuration is run, the UPS LCD screen will report "BPC". The UPS can be reset from BPC to BP0, BP1 or BP2 settings via the LCD screen, but once the new configuration is set, you'll need to run EXTERNAL BATTERY CONFIGURATION TOOL software again to re-configure back to the unique BPC setting. UPS MODEL SU1000XLCD SU1500XLCD SU2200XLCD SU3000XLCD BP0 No BP No BP No BP No BP BP1 Qty 1 BP24V15RT2U Qty 1 BP48V24-2U Qty 1 BP48V24-2U Qty 1 BP72V15-2U BP2 Qty 1 BP24V28-2U Qty 1 BP48V60RT3U Qty 1 BP48V60RT3U Qty 1 BP72V28RT3U ALL OTHER BATTERY PACK CONFIGURATIONS Use EXTERNAL BATTERY CONFIGURATION TOOL software Use EXTERNAL BATTERY CONFIGURATION TOOL software Use EXTERNAL BATTERY CONFIGURATION TOOL software Use EXTERNAL BATTERY CONFIGURATION TOOL software ACCEPT AND ADVANCE To ACCEPT the current value & ADVANCE to the next configuration screen, press the ON/SELECT button (less than 1 second). VIEW ALTERNATE SETTINGS To VIEW ALTERNATE SETTINGS, press the SETUP BUTTON repeatedly (under 1 second each). AVAILABLE VALUES BP0 (factory), BP1, BP2 (BPC reflects a software set configuration) LEAVE UPS SETUP MODE To leave UPS setup mode, PRESS and HOLD the SETUP BUTTON (about 3 seconds). 9 The VIEW IP ADDRESS selection screen will appear. The VIEW IP ADDRESS is a display field that enables viewing of the current UPS IP address when the SNMPWEBCARD option is in use. The UPS is only capable of displaying a IPv4 level IP address when configured with the SNMPWEBCARD. If VIEW IP ADDRESS is attempted for IPv6 level IP address or for a UPS configuration without the SNMPWEBCARD, the LCD screen will report NA. ACCEPT AND ADVANCE To ADVANCE to back to the OUTPUT VOLTAGE selection screen, press the ON/SELECT button (less than 1 second). VIEW ALTERNATE SETTINGS To VIEW IP address information in 3 digit segments, press the SETUP button repeatedly (less than 1 second). LEAVE UPS SETUP MODE To leave UPS setup mode, PRESS and HOLD the SETUP BUTTON (about 3 seconds). 24 13-03-138 93-3168-EN.indd 24 3/28/2013 1:05:44 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
24
Operation
8
The EXTERNAL BATTERY TYPE selection screen will appear.
EXTERNAL BATTERY TYPE refers to the ability for the UPS to become aware of which external
battery pack is connected to the UPS.
Setting the external battery configuration enhances
the accuracy of the MINUTES RUNTIME countdown during power failure conditions. The LCD
interface supports no external batteries with the factory configuration of BP0.
Two additonal
LCD configurable external battery pack options are available under the user selection of BP0,
BP1 & BP2. See the table to determine whether BP1 or BP2 applies to your external battery
pack.
If your battery pack is not listed or you are using more than one of any supported
external battery pack, you must use Tripp Lite’s EXTERNAL BATTERY CONFIGURATION TOOL
software available for download at this link: http://www.tripplite.com/bpconfig
NOTE:
Use the BP0 setting if you plan to use the EXTERNAL BATTERY CONFIGURATION TOOL
software.
After the software configuration is run, the UPS LCD screen will report “BPC”.
The UPS can be reset from BPC to BP0, BP1 or BP2 settings via the LCD screen, but once
the new configuration is set, you’ll need to run EXTERNAL BATTERY CONFIGURATION TOOL
software again to re-configure back to the unique BPC setting.
ACCEPT AND ADVANCE
VIEW ALTERNATE SETTINGS
LEAVE UPS SETUP MODE
To ACCEPT the current value
&
ADVANCE
to
the
next
configuration screen, press
the ON/SELECT button (less
than 1 second).
To VIEW ALTERNATE SETTINGS,
press the SETUP BUTTON
repeatedly
(under
1 second
each).
AVAILABLE VALUES
BP0
(factory),
BP1,
BP2
(BPC reflects a software set
configuration)
To
leave UPS setup mode,
PRESS and HOLD the SETUP
BUTTON (about 3 seconds).
UPS MODEL
BP0
BP1
BP2
ALL OTHER BATTERY PACK CONFIGURATIONS
SU1000XLCD
No BP
Qty 1 BP24V15RT2U
Qty 1 BP24V28-2U
Use EXTERNAL BATTERY CONFIGURATION TOOL software
SU1500XLCD
No BP
Qty 1 BP48V24-2U
Qty 1 BP48V60RT3U
Use EXTERNAL BATTERY CONFIGURATION TOOL software
SU2200XLCD
No BP
Qty 1 BP48V24-2U
Qty 1 BP48V60RT3U
Use EXTERNAL BATTERY CONFIGURATION TOOL software
SU3000XLCD
No BP
Qty 1 BP72V15-2U
Qty 1 BP72V28RT3U
Use EXTERNAL BATTERY CONFIGURATION TOOL software
9
The VIEW IP ADDRESS selection screen will appear.
The VIEW IP ADDRESS is a display field that enables viewing of the current UPS IP address when
the SNMPWEBCARD option is in use.
The UPS is only capable of displaying a IPv4 level IP address
when configured with the SNMPWEBCARD.
If VIEW IP ADDRESS is attempted for IPv6 level IP
address or for a UPS configuration without the SNMPWEBCARD, the LCD screen will report NA.
ACCEPT AND ADVANCE
VIEW ALTERNATE SETTINGS
LEAVE UPS SETUP MODE
To ADVANCE to back to the
OUTPUT VOLTAGE selection
screen, press the ON/SELECT
button (less than 1 second).
To VIEW IP address information
in 3 digit segments, press the
SETUP button repeatedly (less
than 1 second).
To
leave UPS setup mode,
PRESS and HOLD the SETUP
BUTTON (about 3 seconds).
13-03-138 93-3168-EN.indd
24
3/28/2013
1:05:44 PM