Uniden D2997 English Owners Manual - Page 20

Resetting a Handset, Adapter and Battery Information

Page 20 highlights

Liquid Damage CAUTION: If the base is covered in liquid, disconnect the adapter and phone cord from the wall before touching it. If the liquid is only on the exterior housing of the base or handset, wipe it off and use as normal. If you can hear liquid inside the housing: 1. Disconnect all cables and cords and remove all compartment covers. 2. If liquid is leaking from any vent or hole, turn the phone so that vent faces down. If not, place the largest vent face down. 3. Let dry for at least 3 days. Check for liquid inside the phone before replacing compartment covers and reconnecting cords. Resetting a Handset If you have trouble with a handset or if you want to replace one, reset it: 1. Press and hold Flash/exit and Pound (#) at the same time until System Reset displays (about 5 seconds). 2. If you still have the base the handset is registered to, select Deregister HS, then select the handset you want to reset. If you don't have that base anymore, select Base Unavailable. 3. To confirm, select Yes. The handset displays Handset not registered. Registering a Handset If you see a "not registered" message on a handset, you must register it to a base before using it. 1. Place the handset in the base; the display should say Handset Registering. 2. Wait until the handset display says Registration Complete (about 30 seconds), then pick up the handset and press Talk/end. ##If you don't hear a dial tone or the display says Registration Failed, charge the battery completely, then try again. Adapter and Battery Information AC adapter Base Charger Battery pack (with normal use) Part number PS-0034 PS-0035 Input voltage 120V AC, 60 Hz Part number / Capacity BT-1016 / 500mAh, 2.4V DC or BT-1025 / 400mAh, 2.4V DC Talk time about 10 hours Output voltage 7.8V AC 8V AC Standby time about 7 days @ 450mA @ 300mA Battery life about 1 year Use only the supplied AC adapters. Use the proper adapter for the base and any chargers. Do not place the unit in direct sunlight or subject it to high temperatures. 20 - English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24

20 - English
Liquid Damage
CAUTION: If the base is covered in liquid, disconnect the adapter and
phone cord from the wall before touching it.
If the liquid is only on the exterior housing of the base or handset, wipe it off
and use as normal. If you can hear liquid inside the housing:
1. Disconnect all cables and cords and remove all compartment covers.
2. If liquid is leaking from any vent or hole, turn the phone so that vent faces
down. If not, place the largest vent face down.
3. Let dry for at least 3 days. Check for liquid inside the phone before replacing
compartment covers and reconnecting cords.
Resetting a Handset
If you have trouble with a handset or if you want to replace one, reset it:
1. Press and hold
FLASH/EXIT
and
POUND (#)
at the same time until
System Reset
displays (about 5 seconds).
2. If you still have the base the handset is registered to, select
Deregister HS
, then
select the handset you want to reset. If you don't have that base anymore,
select
Base Unavailable
.
3. To confirm, select
Yes
. The handset displays
Handset not registered
.
Registering a Handset
If you see a “not registered” message on a handset, you must register it to a
base before using it.
1. Place the handset in the base; the display should say
Handset Registering
.
2. Wait until the handset display says
Registration Complete
(about 30 seconds),
then pick up the handset and press
TALK/END
.
#
If you don’t hear a dial tone or the display says
Registration Failed
, charge
the battery completely, then try again.
Adapter and Battery Information
AC adapter
Base
Charger
Battery pack (with normal use)
Part number
PS-0034
PS-0035
Part number
/ Capacity
BT-1016 / 500mAh, 2.4V DC
or
BT-1025 / 400mAh, 2.4V DC
Input
voltage
120V AC, 60 Hz
Talk time
about 10 hours
Output
voltage
7.8V AC
@ 450mA
8V AC
@ 300mA
Standby time
about 7 days
Battery life
about 1 year
±
Use only the supplied AC adapters.
±
Use the proper adapter for the base and any chargers.
±
Do not place the unit in direct sunlight or subject it to high temperatures.