ViewSonic M1MINI - Ultra Portable LED Projector with JBL Speaker HDMI and USB - Page 12

Remote Control - Effective Range, Remote Control - Replacing the Batteries

Get ViewSonic M1MINI - Ultra Portable LED Projector with JBL Speaker HDMI and USB PDF manuals and user guides View all ViewSonic M1MINI - Ultra Portable LED Projector with JBL Speaker HDMI and USB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Remote Control - Effective Range To ensure proper function of the remote control follow the steps below: 1. The remote control must be held at an angle within 30° perpendicular to the projector's IR remote control sensor(s). 2. The distance between the remote control and the sensor(s) should not exceed 8 m (26 ft.) IR Receiver NOTE: Refer to the illustration for the location of the infrared (IR) remote control sensor(s). IR Receiver Remote Control - Replacing the Batteries 1. Place the remote control facedown and remove the battery tray from the bottom of the remote control by pressing the side tab and pulling it out. 2. Remove any existing battery (if necessary) and install one CR2032 battery. NOTE: Observe the battery's polarities as indicated. 3. Replace the battery tray by aligning it with the base and pushing it back into position. CR2032 OPEN PUSH RELEASE CR2032 OPEN PUSH RELEASE NOTE: • Avoid leaving the remote control and batteries in excessive heat or a humid environment. • Replace only with the same or equivalent type recommended by the battery manufacturer. • If the battery is drained or if you will not be using the remote control for an extended period of time, remove the battery to avoid damage to the remote control. • Dispose of used batteries according to the manufacturer's instructions and local environment regulations for your region. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
12
Remote Control - Effec°ve Range
To ensure proper func°on of the remote control
follow the steps below:
1.
The remote control must be held at an angle
within 30± perpendicular to the projector’s IR
remote control sensor(s).
2.
The distance between the remote control and
the sensor(s) should not exceed 8 m (26 ſt.)
NOTE:
Refer to the illustra°on for the loca°on
of the infrared (IR) remote control
sensor(s).
IR Receiver
IR Receiver
Remote Control - Replacing the Ba±eries
1.
Place the remote control facedown and remove the ba²ery tray from the bo²om
of the remote control by pressing the side tab and pulling it out.
2.
Remove any exis°ng ba²ery (if necessary) and install one CR2032 ba²ery.
NOTE:
Observe the ba²ery’s polari°es as indicated.
3.
Replace the ba²ery tray by aligning it with the base and pushing it back into
posi°on.
CR2032
OPEN
PUSH
RELEASE
CR2032
OPEN
PUSH
RELEASE
NOTE:
•
Avoid leaving the remote control and ba²eries in excessive heat or a humid
environment.
• Replace only with the same or equivalent type recommended by the
ba²ery manufacturer.
•
If the ba²ery is drained or if you will not be using the remote control for
an extended period of °me, remove the ba²ery to avoid damage to the
remote control.
•
Dispose of used ba²eries according to the manufacturer’s instruc°ons and
local environment regula°ons for your region.