ViewSonic PJD5350LS PJD5350LS User Guide English - Page 48

Installing the dust filter (optional accessory), Installing the dust filter

Get ViewSonic PJD5350LS PDF manuals and user guides View all ViewSonic PJD5350LS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Installing the dust filter (optional accessory) Caution • It is important to clean the dust filter every 100 hours after the dust filter is installed. • Be sure to turn off the projector and unplug it from power source before installing or detaching the filter. • If your projector is ceiling-mounted or is not easily accessible, pay special attention to your personal safety when replacing the dust filter. Installing the dust filter 1. Be sure to turn off the projector and unplug it from power source. 2. As the arrows shown to the right, fit the filter by aligning and inserting it into the projector slots. Make sure it clicks into place. For first time installation: 3. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Filter Settings menu. 4. Press Enter and the Filter Settings page is displayed. 5. Highlight Filter Mode and select "On". The filter timer starts counting and the projector will remind you to clean the filter when the filter is in use for over 100 hours. Caution • Set Filter Mode to On only when using the projector after the dust filter (optional accessory) is properly attached. Failing to do so will result in a shorter lamp life. Obtaining the filter hour information 1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Filter Settings menu. 2. Press Enter and the Filter Settings page is displayed. 3. You will see the Filter Hours information on the menu. Cleaning the dust filter 1. Be sure to turn off the projector and unplug it from power source. 2. Press the latches on the dust filter and remove the filter from the projector. 3. Use a small vacuum cleaner or a soft brush to sweep the dust on the filter away. 4. Re-install the dust filter. 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
40
Installing the dust filter (optional accessory)
Caution
•
It is important to clean the dust filter every 100 hours after the dust filter is installed.
•
Be sure to turn off the projector and unplug it from power source before installing or
detaching the filter.
•
If your projector is ceiling-mounted or is not easily accessible, pay special attention to
your personal safety when replacing the dust filter.
Installing the dust filter
1.
Be sure to turn off the projector and unplug it from power source.
2.
As the arrows shown to the right, fit the filter by
aligning and inserting it into the projector slots.
Make sure it clicks into place.
For first time installation:
3.
Open the OSD menu and go to the
SYSTEM
SETTING: ADVANCED
>
Filter Settings
menu.
4. Press
Enter
and the
Filter Settings
page is
displayed.
5. Highlight
Filter Mode
and select "
On
". The filter timer starts counting and the
projector will remind you to clean the filter when the filter is in use for over 100
hours.
Caution
•
Set Filter Mode to On only when using the projector after the dust filter (optional
accessory) is properly attached. Failing to do so will result in a shorter lamp life.
Obtaining the filter hour information
1.
Open the OSD menu and go to the
SYSTEM
SETTING: ADVANCED
>
Filter
Settings
menu.
2. Press
Enter
and the
Filter Settings
page is displayed.
3.
You will see the
Filter Hours
information on the menu.
Cleaning the dust filter
1.
Be sure to turn off the projector and unplug it from power source.
2.
Press the latches on the dust filter and remove the filter from the projector.
3.
Use a small vacuum cleaner or a soft brush to sweep the dust on the filter away.
4.
Re-install the dust filter.