Home » ViewSonic Manuals » Projectors » ViewSonic Pro8200 » Manual Viewer

ViewSonic Pro8200 PRO8200 User Guide (English) - Page 13

Connection Ports - firmware

UPC - 766907496314

Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Connection Ports 1 2 34 5 67 16 15 14 13 12 11 10 9 8 1 RS-232 When operating the projector via a computer, connect this to the controlling computer's RS-232C port. 2 Monitor Out Connect to a computer display, etc. 3 Component (Y Cb/Pb Cr/Pr) Connect Y Cb/Pb Cr/Pr output from video equipment to this jack. 4 S-Video Connect S-Video output from video equipment to this jack. 5 USB A This connector supports firmware update. 6 HDMI 1 Connect HDMI output from video equipment to this jack. 7 HDMI 2 Connect HDMI output from video equipment to this jack. 8 DC 12V Out 12V DC out 9 MIC in Microphone input jack. 10 Audio Out Connect to a speaker or other audio input equipment. 11 Audio 2 Connect an audio output from video equipment or computer to this jack. 12 Audio 1 Connect an audio output from video equipment or computer to this jack. ViewSonic Pro8200 11

Section	Page
Pro8200_UG_ENG-1.pdf	7
Projector Features	7
Package Contents	8
Projector with Lens Cap	8
AC Power Cord	8
Projector Overview	10
Front View	10
Rear View	11
Bottom View	11
Using the Product	12
Control Panel	12
Connection Ports	13
Remote Control	15
Installing the Batteries	17
1. Open the battery cover in the direction shown.	17
2. Install batteries as indicated by the diagram inside the compartment.	17
3. Close the battery cover into position.	17
Remote Control Operation	18
Connection	19
1. Turn all equipment off before making any connections.	19
2. Use the correct signal cables for each source.	19
3. Ensure the cables are firmly inserted.	19
Connecting a computer or monitor	20
Connecting a computer	20
1. Take the supplied VGA cable and connect one end to the D-Sub output socket of the computer.	20
2. Connect the other end of the VGA cable to the Computer in 1 or Computer in 2 signal input socket on the projector.	20
Connecting a monitor	20
1. Connect the projector to a computer as described in “Connecting a computer” on page 18.	20
2. Take a suitable VGA cable (only one supplied) and connect one end of the cable to the D-Sub input socket of the video monitor.	20
3. Connect the other end of the cable to the Monitor Out socket on the projector.	20
Connecting Video source devices	21
Connecting a Component Video source device	22
1. Take a VGA (D-Sub) to HDTV (RCA) cable, Component Video cable or a Component Video to VGA (D-Sub) adaptor and connect the end...	22
2. If you are using the VGA (D-Sub) to HDTV (RCA) cable and the Component Video to VGA (D-Sub) adaptor, connect the other end of...	22
Connecting an S-Video source device	22
1. Take an S-Video cable and connect one end to the S-Video output socket of the Video source device.	22
2. Connect the other end of the S-Video cable to the S-Video socket on the projector.	22
Connecting a composite Video source device	23
1. Take a Video cable and connect one end to the composite Video output socket of the Video source device.	23
2. Connect the other end of the Video cable to the Video socket on the projector.	23
Operation	24
Powering On/Off the Projector	24
Powering On the Projector:	24
1. Remove the projector lens cap.	24
2. Complete the AC power cord and peripheral signal cable(s) connections.	24
3. Press to turn on the projector. The projector takes a minute or so to warm up.	24
4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.	24
Powering Off the Projector:	24
1. Press to turn off the projector lamp. You will see a message \	24
2. Press again to confirm.	24
3. Disconnect the AC power cord from the electrical outlet and the projector.	24
4. Do not turn on the projector right after power off.	24
Adjusting the Projector Height	25
1. To raise or lower the image, press the elevator button and raise or lower the front of the projector. Release the button to lock the adjustment.	25
2. To level the image on the screen, turn the tilt-adjustment feet to fine-tune the height.	25
Adjusting the Projector Zoom and Focus	25
1. Focus the image by rotating the focus ring. A still image is recommended for focusing.	25
2. Adjust the image size by sliding the zoom ring.	25
Adjusting Projection Image Size	26
Locking control keys	27
1. Press on the projector or remote control.	27
2. A confirmation message is displayed. Select Yes to confirm.	27
Menu Operation	28
How to operate	30
1. Press MENU on the projector or Menu on the remote control to open the OSD menu.	30
2. When OSD is displayed, use p / q to select any feature in the main menu.	30
3. After selecting the desired main menu item, press u to enter sub-menu for feature setting.	30
4. Use p / q to select the desired item and adjust the settings with t / u.	30
5. Press MENU on the projector or Menu on the remote control, the screen will return to the main menu.	30
6. To exit OSD, Press MENU on the projector or Menu on the remote control again. The OSD menu will close and the projector will automatically save the new settings.	30
Maintenance	35
Cleaning the Lens	35
Cleaning the Projector Housing	35
Cleaning the Filter Cover	35
1. Switch the projector off and unplug the AC power cord from the wall socket.	35
2. Remove the filter cover as the illustration shown.	35
3. Clean the filter cover.	35
4. Replace the filter cover.	35
5. Attach the filter cover.	35
6. Plug the power back into the projector.	35
Replacing the Lamp	36
1. Turn off the projector.	37
2. If the projector is installed in a ceiling mount, remove it	37
3. Unplug the power cord.	37
4. Loosen the screw in the side of the lamp cover and remove the cover.	37
5. Remove the screws from the lamp module, raise the handle, and lift out the module.	37
6. Insert the new lamp module into the projector and tighten the screws.	37
7. Replace the lamp cover and tighten the screw.	37
8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.	37
9. Reset the lamp hour. Refer to the “Information” menu.	37
Specifications	38
Dimensions	39
Ceiling mount installation	39
Appendix	40
LED Indicator Messages	40
Compatibility Modes	41
Computer:	41
Video:	42
Troubleshooting	43
Start-up problems	43
Image problems	43
RS-232 Command and Configuration	44