Vonage IP8100-2 Features Guide - Page 25

User Name, Password, Re-type Password, Maximum Idle Time, MAC Address, DHCP Client List

Get Vonage IP8100-2 - VTech Wireless VoIP Phone PDF manuals and user guides
UPC - 735078008305
View all Vonage IP8100-2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Basic Settings Basic Settings • User Name: Enter the user name required by your ISP when you connect to the Internet. Note: you may need to append your ISP's domain suffix to the username, i.e., [email protected]. • Password: Enter the password required by your ISP when you connect to the Internet. • Re-type Password: Re-type the password entered. • Maximum Idle Time: (Default 0) This field specifies the number of minutes of inactivity before your IP8100 series telephone terminates the PPPoE session. To avoid periodic disconnection from the Internet, leave this value set to zero. To allow your computer to disconnect after a period of inactivity, enter the time in minutes. (For example, enter 10 to disconnect 10 minutes after you've stopped using the computer.) • MTU: (Default 1492) Data sent over networks is divided into packets of a certain size. MTU (Maximum Transfer Unit) specifies the largest packet size allowed for transmission over a network. This value typically does not need to be changed. Do not change it unless advised to do so by your Internet Service Provider. • MAC Address: This defaults to the MAC® (Media Access Control) address of the WAN port in the IP8100 series telephone. If your ISP has registered the MAC address of your computer, you can manually enter it here, or use the DHCP Client List to copy it. • DHCP Client List: Lists all MAC addresses of computers that have obtained a DHCP lease from the IP8100 series telephone. If your ISP has registered the MAC address of your computer, select that MAC address from the list, click Copy, then click Apply to save the page settings. Clicking Restore takes you back to the default MAC address value. 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
23
Basic Settings
•
User Name:
Enter the user name required by your ISP when you connect to
the Internet.
Note:
you may need to append your ISP’s domain suffix to the username, i.e.,
•
Password:
Enter the password required by your ISP when you connect to
the Internet.
•
Re-type Password:
Re-type the password entered.
•
Maximum Idle Time:
(Default 0) This field specifies the number of minutes
of inactivity before your IP8±00 series telephone terminates the PPPoE
session. To avoid periodic disconnection from the Internet, leave this value
set to zero.
To allow your computer to disconnect after a period of inactivity, enter the
time in minutes. (For example, enter ±0 to disconnect ±0 minutes after you’ve
stopped using the computer.)
•
MTU:
(Default ±492) Data sent over networks is divided into packets of a
certain size. MTU (Maximum Transfer Unit) specifies the largest packet size
allowed for transmission over a network. This value typically does not need
to be changed. Do not change it unless advised to do so by your Internet
Service Provider.
•
MAC Address:
This defaults to the MAC® (Media Access Control) address
of the WAN port in the IP8±00 series telephone. If your ISP has registered the
MAC address of your computer, you can manually enter it here, or use the
DHCP Client List to copy it.
•
DHCP Client List:
Lists all MAC addresses of computers that have obtained a
DHCP lease from the IP8±00 series telephone. If your ISP has registered the
MAC address of your computer, select that MAC address from the list, click
Copy, then click Apply to save the page settings. Clicking Restore takes you
back to the default MAC address value.
Basic Settings