Vtech CS6929 User Manual - Page 14

Desktop installation, Before use, Charge the battery, Con your telephone

Get Vtech CS6929 PDF manuals and user guides View all Vtech CS6929 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Check the battery level After you have installed the battery, check the battery level on the handset screen. • If the battery icon is , or , then go to Before use section to set the date and time, and set the answering system through voice guide. • If the screen is blank, or flashes, then the battery needs to be charged. Go to Charge the battery section before you do any setting or operation. Charge the battery Place the handset in the telephone base or the charger to charge. The screen shows HANDSET X. The battery is charged. To keep the battery charged, place it in the telephone base or charger when not in use. When it is fully charged, you can expect the following performance: Operation Operating time While in handset use (talking*) Seven hours While in Three and a half speakerphone mode hours (talking*) While not in use (standby**) Five days * Operating times vary depending on your actual use and the age of the battery. ** Handset is not charging or in use. Once you have installed the battery, the handset LCD display indicates the battery status (see the table below). Battery indicators The screen is blank, or shows Put in charger and flashes. The screen shows Low battery and flashes. Battery status The battery has no charge or very little charge. The handset cannot be used. The battery has enough charge to be used for a short time. Action Charge without interruption (at least 30 minutes). Charge without interruption (at least 30 minutes). NOTES • Press CANCEL or place the handset in the telephone base or charger will bypass the set date and time, and voice guide. • For best performance, keep the handset in the telephone base or charger when not in use. • The battery is fully charged after 12 hours of continuous charging. • If you place the handset in the telephone base or the charger without plugging in the battery, the screen displays No battery. To manually set the date and time and the answering system, refer to Configure your telephone and Set your built-in answering system sections. To manually initiate the voice guide, refer to Voice guide under Set your built-in answering system section. 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
8
Check the battery level
After you have installed the battery,
check the battery level on the handset
screen.
If the battery icon is
,
or
, then go
to
Before use
section to set the date
and time, and set the answering
system through voice guide.
If the screen is blank, or
flashes,
then the battery needs to be
charged. Go to
Charge the battery
section before you do any setting or
operation.
Charge the battery
Place the handset in the telephone base
or the charger to charge.
Once you have installed the battery,
the handset LCD display indicates the
battery status (see the table below).
Battery
indicators
Battery
status
Action
The screen
is blank, or
shows
Put
in charger
and
flashes.
The battery
has no
charge or
very little
charge. The
handset
cannot be
used.
Charge
without
interruption
(at least 30
minutes).
The screen
shows
Low
battery
and
flashes.
The battery
has enough
charge to be
used for a
short time.
Charge
without
interruption
(at least 30
minutes).
•
•
The screen
shows
HANDSET X
.
The battery is
charged.
To keep
the battery
charged,
place it in the
telephone
base or
charger when
not in use.
When it is fully charged, you can expect
the following performance:
Operation
Operating time
While in handset
use (talking*)
Seven hours
While in
speakerphone mode
(talking*)
Three and a half
hours
While not in use
(standby**)
Five days
*
Operating times vary depending on your actual
use and the age of the battery.
** Handset is not charging or in use.
NOTES
Press
CANCEL
or place the handset in
the telephone base or charger will bypass
the
set date and time
, and voice guide.
For best performance, keep the handset in
the telephone base or charger when not
in use.
The battery is fully charged after 12 hours
of continuous charging.
If you place the handset in the telephone
base or the charger without plugging
in the battery, the screen displays
No battery
.
To manually set the date and time
and the answering system, refer to
Configure your telephone
and
Set
your built-in answering system
sections.
To manually initiate the voice guide,
refer to
Voice guide
under
Set your
built-in answering system
section
.
•
•
•
•