Waring FP1000 Instruction Manual

Waring FP1000 Manual

Get Waring FP1000 PDF manuals and user guides View all Waring FP1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Waring FP1000 manual content summary:

  • Waring FP1000 | Instruction Manual - Page 1
    COMMERCIAL 2.5 Qt. Dicing Food Processor WANG, COMMERC/Al. cuijnarl 2.50T DICING DOD IMOCEsSom metwaion• 2.5OT DICING FP1000 OPERATING MANUAL
  • Waring FP1000 | Instruction Manual - Page 2
    these: 1. Read all instructions. 2. Blades are extremely sharp. Handle carefully. 3. Your Waring food processor is a piece of authorized service facility for examination, repair or adjustmi 11. The use of attachments not recommended or sold by Waring may cause fire, electric shock or injury. 12. Do
  • Waring FP1000 | Instruction Manual - Page 3
    GROUNDING INSTRUCTIONS For your protection, this appliance is equipped with a 3-conductor cordset. 120 volt units are supplied with a molded 3-prong grounding-type plug (NEMA5-15P), and should
  • Waring FP1000 | Instruction Manual - Page 4
    Discs Julienne Discs Troubleshooting Safety Reset Switch Cleaning Limited Warranty pg. 1 pg. 2 pg. 3 pg, 6 pg. 8 pg. 8 pg. 10 pg. 10 pg. 11 pg. 12 pg. 12 pg. 14 pg. 15 pg. 15 pg. 16 pg. 16 pg. 16 pg. 17 pg. 18 pg. 18 pg. 20 THE PARTS The Waring® FP1000 Dicing Food Processor is compact and
  • Waring FP1000 | Instruction Manual - Page 5
    for large foods and provides controlled processing for small diameter foods such as Reset Switch Note that all of the FP1000's accessory discs have a unique offset stem. The accessories. All the stems except the dicing assembly can be easily removed for cleaning in accordance with NSF guidelines. 12
  • Waring FP1000 | Instruction Manual - Page 6
    Batch Bowl 5c 5b Continuous Feed 5c 5b 13 12 - 4 "="
  • Waring FP1000 | Instruction Manual - Page 7
    shaft. • Select the appropriate accessory disc: Grating disc, shredding disc, slicing disc, waved slicing disc, pulping disc, julienne/French fry disc, or dicing grid. • Each of these discs has a disc stem. The disc stem fits over the double flat in the food processor's stainless steel motor shaft
  • Waring FP1000 | Instruction Manual - Page 8
    on the shredding /grating nodules. • Carefully guide the center disc hub over the metal shaft so . NOTE: DO NOT PUT ANY FOOD IN THE BOWL BEFORE PLACING THE ACCESSORY DISC ONTO THE SHAFT. • Place food processor to operate. This is an important safety feature. NEVER ATTEMPT TO START THE FOOD PROCESSOR
  • Waring FP1000 | Instruction Manual - Page 9
    Accessory Disc • Do not remove the work bowl until the accessory disc has been removed. • To remove an accessory PARTS • Clean and sanitize the motor base, and wash, rinse, and sanitize the continuous feed chute, cover, slinger disc, food pusher, food cord until the processor is completely assembled.
  • Waring FP1000 | Instruction Manual - Page 10
    accessory disc: Grating disc, shredding disc, slicing disc, waved slicing disc, pulping disc, or julienne/French fry disc. • Each of these discs has a disc stem. The disc stem fits over the double flat in the food processor shredding/grating nodules. • Carefully guide the disc stem over the metal
  • Waring FP1000 | Instruction Manual - Page 11
    food pusher. The large pusher is for processing larger vegetables. The smaller pusher nests in the larger pusher and can be used for smaller vegetables, guiding long thin vegetables for more precise cuts and for jobs like slicing pepperoni. DISASSEMBLY OF CONTINUOUS FEED CHUTE PARTS food processor.
  • Waring FP1000 | Instruction Manual - Page 12
    to any texture or consistency you want, from coarse to fine. • Pulsing is also useful in processing hard foods. Pulse the food a few times to break up into smaller parts. Then proceed with continuous use after the pieces are broken up and easier to process. • Always use the PULSE /OFF lever for
  • Waring FP1000 | Instruction Manual - Page 13
    food processor is running. It is recommended that the Food used when slicing foods where a same food pushers. They are interchangeable. USE INSTRUCTION for instructed in the section titled, "Assembling the Batch Bowl Parts." Chopping & Mincing • To chop or mince in the bowl, fill the bowl with food
  • Waring FP1000 | Instruction Manual - Page 14
    pulse button until the desired consistency has been reached. If the machine has trouble starting, reduce the amount of meat in the bowl and start again. . Turn the Machine OFF with the OFF Switch. •Always switch the food processor off by pressing and releasing the PULSE/OFF switch. This assures that
  • Waring FP1000 | Instruction Manual - Page 15
    ", or assemble the continuous feed chute and accessory disc as instructed in the section titled "Assembling the Continuous Feed Chute Parts". • If required by your processing task, either: Stack the feed tube with food product and position the large food pusher at the top of the stack, or Place the
  • Waring FP1000 | Instruction Manual - Page 16
    feature: Select dicing grid and place in chute on top of "posts" support. Pick up slicing disc either by using the finger holes on disc surface end of this manual under "Processing Tools". Three (3) Accessory Discs and one Dicing Assembly are included with both the FP1000 food processors. As of
  • Waring FP1000 | Instruction Manual - Page 17
    BFP31 5/32" BFP32 1/16" Size Millimeters 5 mm 6.5 mm 8 mm 10 mm Size Inches 3/16" 1/4" 5/16" 3/8" Pulping/Grating/Shredding Discs Waring Size Size Waring Size Size Item No. Millimeters Inches Item No. Millimeters Inches BFP17 0.4 mm Pulping 1/64" BFP22 4 mm Shredding 5/32" BFP19
  • Waring FP1000 | Instruction Manual - Page 18
    and the correct solutions for them. Problems which cannot be solved with the guidelines listed below should be referred to one of the Waring Authorized Service Centers for assistance. A listing of authorized service agencies is provided with each Waring food processor. Unit does not start when
  • Waring FP1000 | Instruction Manual - Page 19
    provided for your convenience and to extend the useful life of your Waring food processor. It is located on the back of your machine, on the the food processor and accessories prior to initial use and after each use. Do not use harsh abrasive-type cleaners on any part of the food processor. Cleaning
  • Waring FP1000 | Instruction Manual - Page 20
    have aluminum components. Whether cleaning them manually or in a dishwasher, be sharp. Please note that all accessory discs and blades may be part of the Commercial Food Processor. TO CLEAN DICING GRID: Using tool provided, push food out of grid from the back side. NOTE: Do not push food
  • Waring FP1000 | Instruction Manual - Page 21
    Waring warrants it's new Waring Commercial Food Processors, models FP25/FP25C, FP40, FP40C, FP1000, Waring Commercial Division will repair or replace any part which, upon our examination, is defective in materials or workmanship, provided the product is delivered prepaid to the Waring Service
  • Waring FP1000 | Instruction Manual - Page 22
    PL NSF® C US LISTED COMMERCIAL 314 Ella T. Grasso Ave. Torrington, CT 06790 1-800-4-WARING www.waringproducts.com U IB-4889
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
COMMERCIAL
2.5
Qt.
Dicing
Food
Processor
WANG,
COMMERC/Al.
cuijnarl
2.50T
DICING
DOD
IMOCEsSom
•••••••.-metwaion•
2.5OT
DICING
FP1000
OPERATING
MANUAL