Waring MXE2000 Instruction Manual - Page 4

6

7

GETTING STARTED/CHARGING YOUR ELLIPSE DRIVE

CAUTION:

Store the Ellipse chargers and Ellipse drive at room temperature

only. Avoid exposure to high temperatures to prevent damage.

1.

Your Ellipse Blending System comes with one single charging station.

Please ensure you fully charge your Ellipse drive before using it for the

first time and after every service day.

2. Plug your adapter into a wall outlet.

3.

Before first use, place your Ellipse drive on the charging station and

charge for 2.5-3 hours. The LED will indicate your battery level.

a. Low battery (1-25%) = Blinking red

b. Medium battery (26-75%) = Blinking orange

c. High battery (76-99%) = Blinking green

d. Full battery (100%) = Solid green

4.

Once your drive has reached the solid green stage, your Ellipse drive

is fully charged and ready to use.

OPERATING YOUR ELLIPSE DRIVE

1.

The Ellipse drive can be activated in two ways, automatically and manually:

–

Automatic activation:

The Ellipse drive needs to be

activated by pressing and holding the AUTO START

button for three seconds (see figure 1). When the

drive is active, you’ll see the green LED blinking.

This indicates your drive is now in AUTO START

mode. The Ellipse drive can be activated

automatically by closing the sound enclosure.

Once activated, the drive will run continuously

for 30 seconds or until the sound enclosure is opened.

NOTE:

In AUTO START mode, do not store the drive upside down.

–

Manual activation:

The Ellipse drive can also be

activated by pressing one of the three buttons on top

of the drive at any time (see figure 2). Each button

indicates the duration the drive will remain on —

10 seconds, 20 seconds or 30 seconds—depending

on your specific blending needs.

NOTE:

To stop or cancel any automatic or manually

activated mode, press any of the time buttons again.

2. To turn off AUTO START mode on your Ellipse drive, press and hold the

AUTO START button for three seconds. You can confirm the drive is off if

the LED is no longer blinking.

3.

At the end of every service day, place the drive on the provided charger to

ensure your drive is fully charged for the next service day or shift.

NOTE:

The Ellipse drive will fully charge in 3 hours. Each full charge

can last up to 8 hours, depending on use.

FIGURE 1

FIGURE 2

NOTE:

Use a soft, damp cloth to clean the clear window of the

Ellipse drive. This will ensure the drive runs properly.

NOTE:

Do not overcharge the Ellipse drive. Ellipse drive should not

be left on charging station indefinitely. This will degrade the battery

over time. To preserve battery life of the Ellipse drive, only charge

when needed.

4. Please ensure the Ellipse dasher and lid are in place before placing the

drive on the jar.

NOTE:

When blender is not in use, place Ellipse drive on the docking

station for easy access.

ELLIPSE DASHER SYSTEM

1. The Ellipse dasher system is made up of two primary

parts. Each individual piece cannot operate without

the other.

2.

Assembly:

The dasher features two locking tabs on each

of its sides. In order to properly assemble the

dasher into the lid, insert the dasher into the bottom of

the lid (as shown in the image to the right) until each

of the locking tabs clicks into place. Once in place, the

dasher is securely locked to the lid and can be placed

on the Ellipse jar.

3.

Disassembly:

In order to disassemble the dasher from

the lid, gently press inward on the two locking tabs.

This will disengage the dasher from the lid. Gently press

down on the locking tabs pushing through the lid using both thumbs.

NOTE:

Please perform this operation over a sink or counter to prevent the

dasher from falling and being damaged.

NOTE:

The Ellipse lid features two gaskets, one located on the inside

of the lid and the second located around the outside of the lid. Both

gaskets must be in place in order to properly run the Ellipse system.

Both gaskets must be removed and cleaned at the end of each service

day or as needed.

ELLIPSE DOCKING STATION

Your Ellipse blender comes with a docking station that functions as a

storage option for your Ellipse drive. The docking station can be placed in front

of your blender base or on the right or left side, depending on your storage

and/or usage needs.

NOTE:

The docking station is not a charging device. It will not charge your

Ellipse drive when in place.

Lid

Dasher

Waring MXE2000 Instruction Manual - Page 4

Getting Started/charging Your Ellipse Drive, Operating Your Ellipse Drive, Ellipse Dasher System,

Page 4 highlights