Waring MXE2000 Instruction Manual - Page 6

NOTE: The button will act as the enter key to proceed to the next step during the reprogramming process. 1. To enter new program, press both Speed Up and Speed Down buttons simultaneously while unit is in STANDBY mode. The blender will enter new programming mode and the LCD will prompt "ADD NEW PROGRAM." 2. Next, you will need to set values. Press the Program button you want to replace (e.g., 1-4). The LCD will prompt "USE UP/DOWN TO SET SPEED: 25%." NOTE: 25% is the default speed setting in the reprogramming mode. 3. Press Speed Up or Speed Down button to set the speed value. The increment is 1% (150 RPM). Press and hold the button to quickly scroll through speeds. The speed can be set between 5% and 100%. 4. Once desired speed is reached, press button or wait 5 seconds to confirm setting. The LCD will now prompt "USE UP/DOWN TO SET TIME." NOTE: Five seconds is the default time setting in the reprogramming mode. 5. Use Speed Up or Speed Down button to set the time value (up to 90 seconds). Once 90 seconds is reached, pressing Speed Up will not increase the value and the LCD will prompt "MEMORY LIMIT" for 2 seconds. 6. Press button or wait 5 seconds to confirm the setting. When the blending time is confirmed, the LCD will prompt SELECT ANOTHER SPEED. Repeat steps 3-5 if additional processing is needed. NOTE: When pressing Speed Up or Speed Down buttons to set speed for next section, the LCD will prompt "USE UP & DOWN TO SET SPEED: 25%." 7. To save the new program settings, press both Speed Up and Speed Down buttons simultaneously. The LCD will prompt NEW PROGRAM (PROG #) SAVED for 5 seconds. The blender will return to STANDBY mode and the LCD will prompt "PRESS ANY BUTTON TO BLEND." NOTE: If no button is pressed within 60 seconds after prompt to "ADD NEW PROGRAM," the blender will exit NEW PROGRAM mode and will return to STANDBY mode. The new program will not be stored. 8. To run new programs, simply press the desired Program button and the blender will run the program set by the user. The LCD will display NEW PROGRAM # and will count down the set time. RESTORING FACTORY-SET BEVERAGE STATIONS 1. To restore factory-set default beverage stations, press both Speed Up and Speed Down buttons. LCD will prompt "ADD NEW PROGRAM." 2. Press button. LCD will prompt "RESTORE DEFAULT PROGRAMS." 10 3. Press button to confirm and save. The LCD will display the logo for 3 seconds. 4. The unit will return to STANDBY mode and the LCD will prompt "PRESS ANY BUTTON TO BLEND." NOTE: The STOP key will abort this process at any point before restoring default programs is confirmed. DRINK COUNTER Your reprogrammable blenders are equipped with a drink counter to keep track of daily drink totals and total drink counts for your machine. To display the counts, hold program buttons & simultaneously for 3 seconds. Your display will read: DAILY COUNT XXXX TTL COUNT XXXXX Daily Count will display the number of drinks mixed per day. Total Count is the accumulation of all drinks made since first use of the blender. The Daily Count can be reset by holding in Program buttons & simultaneously for 3 seconds, then pressing ON/OFF button for 3 seconds. Daily Count will reset to zero and Total Count will remain unchanged. If Total Count needs to be reset, call your nearest Waring authorized service facility for information. NOTE: Use of the PULSE features will not add to the daily or total drink counts. RESETTING THERMAL PROTECTION • T he blender you have purchased is equipped with an automatic reset switch to protect the motor from overheating. • If your blender stops running under heavy use, turn the power switch to the STANDBY or OFF position and unplug the power cord. Empty the blender container of all its contents and allow approximately 5 minutes for the motor to cool down. • Plug the power cord back into the outlet and continue blending. READY TO BLEND 1. Once your blender is properly programmed and your jar is placed on the blender base, you're ready to start blending. Determine if you will be using the Ellipse drive in manual or auto mode. If manual mode is needed, press your desired timing. If AUTO START is needed, activate the drive by pressing the button for 3 seconds. 2. Close the sound enclosure lid. 3. Press the applicable blend station setting (1-4). The Ellipse will blend to your predetermined settings. 11