Weber Genesis Jr NG Owner Manual - Page 13

Add cooking

Get Weber Genesis Jr NG PDF manuals and user guides View all Weber Genesis Jr NG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Step 7 Add cooking box Guide screw You will need: frame assembly, cooking box assembly, 1/4-20 x 2 inch bolt, 1/4 inch nylon washer, 1/4-20 acorn nut, pliers and a 7/16 inch open-end or an adjustable wrench. (a) Set the cooking box into the frame so the burner tubes (b) are under the frame brace. Figure 6. Burner tubes Frame brace View from below (c) and behind cooking box Figure 6 Your Weber Genesis Gas Barbecue burner assembly has been factory assembled, pressure and flame tested. As a safety precaution we recommend you check the burner alignment: a) Do the valves fit into the ends of the burners? Figure 7 (a). b) Are the ends of the burners under the washers at the left rear and left front of the cooking box? The screws are only guides. Do not tighten. Figure 7 (b). c) Are the thumb screws under the burner assembly hand tight? Do not tighten with pliers. Figure 7 (c). If you answered YES to a, b and c, the burners are correctly aligned. If you answered NO, the burners are misaligned. Contact your dealer. Do not use barbecue. Figure 7 Thumb screws Slide the cooking box to the left within the frame. Put washer on bolt. Insert the bolt through the cooking box and frame with the head of the bolt outside the box. Figure 8. Add the nut. Tighten by holding the bolt with pliers while you tighten the nut with a wrench. 0 Figure 8 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
Step
7
Add cooking
box
You
will
need:
frame
assembly,
cooking
box
assembly,
1/4-20
x 2
inch
bolt,
1/4
inch nylon
washer,
1/4-20
acorn
nut, pliers
and
a
7/
1
6
inch
open-end
or
an
adjustable
wrench.
Set
the
cooking box
into the
frame
so
the
burner tubes
are
under the frame brace.
Figure
6.
Burner
tubes
Frame brace
Figure
6
Your
Weber
Genesis
Gas
Barbecue burner assembly
has
been
factory assembled, pressure
and
flame tested.
As
a
safety precaution we
recommend you check the
burner alignment:
a) Do
the valves
fit into the
ends
of the burners?
Figure
7
(a).
b)
Are the
ends of
the
burners
under
the washers
at
the
left
rear
and
left
front
of the cooking box?
The
screws
are only guides. Do
not
tighten. Figure
7
(b).
c)
Are the thumb
screws
under
the
burner
assembly
hand tight?
Do
not
tighten
with pliers. Figure
7
(c).
If
you answered YES
to a,
b
and
c,
the burners are
correctly
aligned.
If
you answered NO,
the
burners are
misaligned.
Contact
your
dealer.
Do
not use
barbecue.
Guide screw
(b)
Figure
7
(c)
(a)
View
from
below
and
behind
cooking
box
Thumb
screws
Slide the cooking
box
to
the
left
within
the
frame.
Put
washer
on
bolt. Insert the bolt
through
the
cooking
box
and
frame
with
the head
of
the
bolt
outside
the
box.
Figure
8.
Add
the nut.
Tighten
by
holding
the bolt with
pliers while you tighten the
nut
with
a
wrench.
0
Figure
8
13