Weber Genesis Jr NG Owner Manual - Page 21

Swing, table, installation, continued, Complete, accessory

Get Weber Genesis Jr NG PDF manuals and user guides View all Weber Genesis Jr NG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Swing table installation continued Put the spacer on the swing table hinge rod and slip the hinge rod into the hole in the frame at the front end of the Weber Genesis Gas Barbecue. Figure 25 (a). With the swing table and rod down, slip the other end of the hinge rod into the hinge support. While holding the table and the hinge support, install the hinge support to frame. Insert screw from outside, put star washer on the inside and start tightening the nut. Tighten with a screwdriver. Figure 25 (b). Push rod cover on end of hinge rod sticking through hinge support. Install rod holder on leg. Figure 25 (c). Hook the support rod into the support rod holder. Spacer (a) - 0 Step 20 Complete accessory installation You will need: work table, two accessory trays, warming rack, thermometer, four tubing plugs and a hammer. Set the work table onto the right side rails. Figure 26 (a). Set the accessory trays between the two frame connectors. Figure 26 (b). Open the lid and set the warming rack into the slots at the rear of the cooking box. Figure 26 (c). Insert the thermometer into its holder. Figure 26 (d). Insert the tubing plugs into the ends of the frame. To fully seat the plugs, you may have to tap them lightly with a hammer. Figure 26 (e). (C) 0 (d) (e) View from rear (b) of barbecue (b) 0 (5) Rod cover 0 (c) 0 Figure 25 21 (a) Figure 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
Swing
table
installation
continued
Put
the
spacer
on the swing table hinge
rod
and slip
the
hinge
rod
into
the
hole
in
the frame
at the front end
of
the
Weber
Genesis
Gas
Barbecue. Figure
25
(a). With
the
swing
table
and rod down, slip
the
other
end
of the
hinge
rod into the
hinge
support. While holding
the
table
and the
hinge support,
install
the
hinge support
to
frame.
Insert screw
from
outside, put
star
washer
on the
inside
and start
tightening
the nut.
Tighten
with
a
screwdriver.
Figure
25
(b).
Push
rod
cover
on end
of
hinge
rod
sticking through
hinge
support.
Install
rod
holder
on
leg.
Figure
25
(c). Hook the support
rod into
the
support
rod
holder.
(b)
0
(5
)
Rod
cover
Spacer
(a)
-
Figure
25
0
View
from
rear
of
barbecue
0
0
(c)
Step
20
Complete
accessory
installation
You
will
need:
work
table, two
accessory
trays,
warming
rack,
thermometer,
four
tubing
plugs
and
a
hammer.
Set
the
work
table onto
the
right
side
rails.
Figure
26
(a).
Set
the
accessory
trays between the two frame
connectors. Figure 26
(b).
Open
the
lid and
set
the
warming
rack
into
the slots
at
the rear
of
the cooking
box.
Figure
26 (c).
Insert the thermometer
into
its
holder.
Figure
26
(d).
Insert the tubing
plugs into
the ends
of
the frame.
To
fully
seat the
plugs,
you may
have
to tap
them lightly
with
a
hammer.
Figure
26
(e).
(C)
0
(b)
(d)
Figure
26
(a)
(e)
21