Weider Club 16.8st English Manual - Page 16
Wrap the Low Cable 72 over a 4² Pulley 35. Slide
View all Weider Club 16.8st manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 16 highlights
32. Locate the Low Cable (72), which is the only remaining Cable. Note that it has a large ball on one end and a small ball on the other. Route the small ball on the Low Cable (72) through the indicated slots in the Leg Lever (29) and the front leg on the Base (8). Attach a 4Ó Pulley (35) inside the slot in the front leg of the Base (8) with a 3/8Ó x 2 1/2Ó Bolt (54), two 3/8Ó Flat Washers (55), two 5/8Ó x 1/2Ó Pulley Bushings (42), and a 3/8Ó Nylon Jam Nut (63). 33. Attach a 4Ó Pulley (35) inside the slot in the Leg Lever (29) with a 3/8Ó x 2 1/2Ó Bolt (54), two 3/8Ó Flat Washers (55), two 5/8Ó x 1/2Ó Pulley Bushings (42), and a 3/8Ó Nylon Jam Nut (63). Attach the 1/2Ó x 1 3/4Ó Bushing (94) inside the bottom of the Leg Lever (29) with a 5/16Ó x 2 1/2Ó Bolt (96), two 5/16Ó Flat Washers (80), and a 5/16Ó Nylon Jam Nut (79). Refer to the inset drawing. Press the Tab (93) onto the cage as shown. Secure the Tab with a 1/4Ó x 1Ó Bolt (95), a Large Washer (104), and a 1/4Ó Nylon Locknut (25). Make sure that the Low Cable (72) is on top of the Tab and the 1/2Ó x 1 3/4Ó Bushing (94). 32 72 35 8 42 29 42 54 55 Large Ball 63 55 Slots 33 80 42 55 63 79 33 29 Slot 54 55 42 35 Cage 72 94 96 95 72 93 104 25 Press a 2Ó Square Inner Cap (33) into the bottom of the Leg Lever (29). Note: It may be easier to attach 34 the 2Ó Square Inner Cap and the 1/2Ó x 1 3/4Ó Bushing (94) if you pivot the Leg Lever upward. 34. Route the Low Cable (72) through the indicated slot in the Main Upright (3) and the Base (8). Wrap the Low Cable (72) around a 4Ó Pulley (35) in the direction shown. Attach the Pulley inside the welded bracket on the Main Upright (3) with a 3/8Ó x 2Ó Bolt (62) and a 3/8Ó Nylon Locknut (50) as shown. 35 62 72 50 Bracket 3 Slot 8 35. Wrap the Low Cable (72) over a 4Ó Pulley (35). Slide the Pulley and a Cable Trap (44) between the two 35 Pulley Plates (31). Make sure the Cable is in the groove of the Pulley and that the Cable Trap is oriented so it will hold the Cable in place. 31 Attach the 4Ó Pulley (35) and the Cable Trap (44) to Adjustment the lowest holes in the Pulley Plates (31) with a 3/8Ó x Holes 63 1 3/4Ó Bolt (60) and a 3/8Ó Nylon Jam Nut (63). 60 44 72 35 16