Weider Club C 725 English Manual - Page 28

the Low Cable.

Get Weider Club C 725 PDF manuals and user guides View all Weider Club C 725 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

57. Wrap the Low Cable (80) under a Small Pulley (74). Attach the Small Pulley and two Half Pulley 57 Guards (91) to the Weight Carriage Base (20) with an M10 x 45mm Button Bolt (131) and an M10 Nylon Locknut (116). Make sure that the Half Pulley Guards are oriented as shown. 91 116 80 74 91 20 131 58. Attach the Low Cable (80) to the "U"-bracket (90) 58 with an M8 Nylon Locknut (139) and an M8 Washer (84) (see the inset drawing). Tighten the Nylon Locknut exactly two full turns onto the Low Cable. 90 139 84 80 139 84 90 80 59. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in ADJUSTMENT, beginning on the following page. Note: After assembly is completed, some extra parts may be left over. Before using the weight bench, pull each cable a few times to make sure that the cables move smoothly over the pulleys. If one of the cables does not move smoothly, find and correct the problem. IMPORTANT: If the cables are not properly installed, they may be damaged when heavy weight is used. See the CABLE DIAGRAM on page 34 for proper cable routing. If there is any slack in the cables, you will need to remove it by tightening the cables (see MAINTENANCE on page 33). 28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
28
57. Wrap the Low Cable (80) under a Small Pulley
(74). Attach the Small Pulley and two Half Pulley
Guards (91) to the Weight Carriage Base (20)
with an M10 x 45mm Button Bolt (131) and an
M10 Nylon Locknut (116).
Make sure that the
Half Pulley Guards are oriented as shown.
58
139
80
131
80
84
91
57
80
90
139
84
59. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in
ADJUSTMENT, beginning on the following page.
Note: After assembly is completed, some extra parts
may be left over.
Before using the weight bench, pull each cable a few times to make sure that the cables move smoothly
over the pulleys. If one of the cables does not move smoothly, find and correct the problem.
IMPORTANT: If
the cables are not properly installed, they may be damaged when heavy weight is used. See the
CABLE DIAGRAM on page 34 for proper cable routing. If there is any slack in the cables, you will
need to remove it by tightening the cables (see MAINTENANCE on page 33).
90
20
58. Attach the Low Cable (80) to the “U”-bracket (90)
with an M8 Nylon Locknut (139) and an M8
Washer (84)
(see the inset drawing). Tighten
the Nylon Locknut exactly two full turns onto
the Low Cable.
116
74
91