Weslo Gym 3000 Uk Manual - Page 12

IMPORTANT: The Short and Long Cables 23

Get Weslo Gym 3000 PDF manuals and user guides View all Weslo Gym 3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

22. Wrap the Long Cable (66) up around the 3 1/2" Pulley (15) on the right Arm (46). Tighten the 3/8" x 1 3/4" Bolt (48) and 3/8" Nylon Locknut (not shown). Make sure that the Cable Trap (59) is turned to the indicated position. Attach the 5/16" x 3" Bolt (17), two 5/16" Flat Washers (8), and a 5/16" Jam Nut (2) to the indicated hole in the Top Frame (67). Slide the end of the Long Cable (66) onto the 5/16" x 3" Bolt (17). Tighten another 5/16" Jam Nut (2) onto the Bolt. 22 67 17 66 22 15 48 8 12 9 3 59 6 46 23. Hold the indicated end of the Short Cable (23) under the 3 1/2" Pulley (15) on the Front Upright (42). Attach the 5/16" x 3 1/2" Bolt (87), two 5/16" Flat Washers (8), the 1" Metal Spacer (22), and a 5/16" Nylon Locknut (3) to the Front Upright as shown. Make sure that the Short Cable is between the Pulley and the Metal Spacer. Tighten the 3/8" Nylon Locknut (21) and 3/8" x 3 1/2" Bolt (not shown). Wrap the Short Cable (23) up around the 3 1/2" Pulley (15) on the Pulley Plate (20). Tighten the 3/8" Nylon Locknut (21) and 3/8" x 1 3/4" Bolt (48). Make sure that the Cable Trap (59) is in the 6 oʼclock position. 24. Remove the 3/8" Nylon Locknut (21), 3/8" x 1 3/4" Bolt (48), and 4 1/2" Pulley (77) from the lower end of the "I" Plates (78). Route the Short Cable (23) over the Pulley and reattach the Pulley to the "I" Plates with the Bolt and Nylon Locknut. Refer to the inset drawing. Slide the Plastic Flanged Bushing (103) onto the Weight Tube (80). Press the Plastic Flanged Bushing into the top Weight (25). Slide the Weight Guide Bracket (81) onto the top of the Weight Tube. Tap the Weight Guide Bracket with a mallet to ensure that the Plastic Flanged Bushing is firmly in the top Weight. Insert the end of the Short Cable (23) into the upper end of the Weight Tube (80). Insert a 5/16" x 1 1/2" Bolt (24) through the Weight Guide Bracket (81), Weight Tube, and Short Cable. Tighten a 5/16" Nylon Locknut (3) onto the Bolt. IMPORTANT: The Short and Long Cables (23, 66) must be properly routed on the Pulleys, and the Cables must be properly tightened. To tighten the Cables, refer to TIGHTENING THE CABLES on page 18 of this manual. 23 12 9 3 6 59 48 15 15 87 8 20 22 21 23 3 8 42 24 66 3 103 25 23 78 81 24 21 48 77 23 80 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
12
22. Wrap the Long Cable (66) up around the 3 1/2”
Pulley (15) on the right Arm (46). Tighten the 3/8”
x 1 3/4” Bolt (48) and 3/8” Nylon Locknut (not
shown).
Make sure that the Cable Trap (59) is
turned to the indicated position.
Attach the 5/16” x 3” Bolt (17), two 5/16” Flat
Washers (8), and a 5/16” Jam Nut (2) to the indi-
cated hole in the Top Frame (67).
Slide the end of the Long Cable (66) onto the
5/16” x 3” Bolt (17). Tighten another 5/16” Jam
Nut (2) onto the Bolt.
23. Hold the indicated end of the Short Cable (23)
under the 3 1/2” Pulley (15) on the Front Upright
(42). Attach the 5/16” x 3 1/2” Bolt (87), two 5/16”
Flat Washers (8), the 1” Metal Spacer (22), and a
5/16” Nylon Locknut (3) to the Front Upright as
shown.
Make sure that the Short Cable is
between the Pulley and the Metal Spacer.
Tighten the 3/8” Nylon Locknut (21) and 3/8” x
3 1/2” Bolt (not shown).
Wrap the Short Cable (23) up around the 3 1/2”
Pulley (15) on the Pulley Plate (20). Tighten the
3/8” Nylon Locknut (21) and 3/8” x 1 3/4” Bolt
(48).
Make sure that the Cable Trap (59) is in
the 6 oʼclock position.
24. Remove the 3/8” Nylon Locknut (21), 3/8” x 1 3/4”
Bolt (48), and 4 1/2” Pulley (77) from the lower
end of the “I” Plates (78). Route the Short Cable
(23) over the Pulley and reattach the Pulley to the
“I” Plates with the Bolt and Nylon Locknut.
Refer to the inset drawing. Slide the Plastic
Flanged Bushing (103) onto the Weight Tube
(80). Press the Plastic Flanged Bushing into the
top Weight (25). Slide the Weight Guide Bracket
(81) onto the top of the Weight Tube.
Tap the
Weight Guide Bracket with a mallet to ensure
that the Plastic Flanged Bushing is firmly in
the top Weight.
Insert the end of the Short Cable (23) into the
upper end of the Weight Tube (80). Insert a 5/16”
x 1 1/2” Bolt (24) through the Weight Guide
Bracket (81), Weight Tube, and Short Cable.
Tighten a 5/16” Nylon Locknut (3) onto the Bolt.
IMPORTANT: The Short and Long Cables (23,
66) must be properly routed on the Pulleys,
and the Cables must be properly tightened. To
tighten the Cables, refer to TIGHTENING THE
CABLES on page 18 of this manual.
12
3
6
9
23
24
87
48
59
8
22
23
23
66
81
3
25
103
80
23
78
77
48
21
24
8
3
15
42
15
21
20
12
3
6
9
22
66
67
2
2
46
8
17
15
48
59