Weslo Pursuit 30 English Manual - Page 13

Note: The con

Get Weslo Pursuit 30 PDF manuals and user guides View all Weslo Pursuit 30 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

As you pedal, the RPM meter on the left side of the display will indicate your approximate pedaling pace in revolutions per minute (RPM). The lowest bar on the RPM meter indicates a pedaling pace of 30 rpm. Additional bars will appear in increments of 10 rpm. Note: The console can show speed and distance in either miles or kilometers. The letters "mph" or "km/h" will appear in the display to show which unit of measurement is selected. To change the unit of measurement, first hold down the Display button for several seconds. An "E" for English miles or an "M" for metric kilometers will appear in the display. Press the Magnetic Resistance increase button repeatedly until the desired unit of measurement appears in the display. Then, press the Resistance / Pace Workouts button to save your selection. 5. Measure your heart rate if desired. To measure your heart rate, stop pedaling and place your thumb on the pulse sensor. Do not press too hard, or the circulation in your thumb will be restricted and your pulse will not be detected. After a few seconds, the heartshaped indicator in the display will flash steadily, two dashes will appear, and then your heart rate will be shown. Hold your thumb on the pulse sensor for about 15 seconds for the most accurate reading. If the displayed heart rate appears to be too high or too low, or if your heart rate is not displayed, lift your thumb off the pulse sensor for a few seconds. Then, place your thumb on the pulse sensor as described above. To reset the display, press the On/Reset button. To pause the console, stop pedaling. When the console is paused, the time will flash in the display. To continue your workout, simply resume pedaling. Make sure you are applying the proper amount of pressure to the pulse sensor. Try the pulse sensor several times until you become familiar with it. Remember to remain still while measuring your heart rate. 6. When you are finished exercising, the console will turn off automatically. If the pedals do not move for a few seconds, the time will flash in the display and the console will pause. If the pedals do not move for a few minutes, the console will turn off and the display will be reset. 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
13
As you pedal, the RPM meter on the left side of
the display will indicate your approximate pedaling
pace in revolutions per minute (RPM). The lowest
bar on the RPM meter indicates a pedaling pace
of 30 rpm. Additional bars will appear in incre-
ments of 10 rpm.
Note: The con-
sole can show
speed and dis-
tance in either
miles or kilome-
ters.
The letters
“mph” or “km/h”
will appear in the
display to show which unit of measurement is
selected. To change the unit of measurement, first
hold down the Display button for several seconds.
An “E” for English miles or an “M” for metric kilo-
meters will appear in the display. Press the
Magnetic Resistance increase button repeatedly
until the desired unit of measurement appears in
the display. Then, press the Resistance / Pace
Workouts button to save your selection.
To reset the display, press the On/Reset button.
To pause the console, stop pedaling. When the
console is paused, the time will flash in the dis-
play. To continue your workout, simply resume
pedaling.
5.
Measure your heart rate if desired.
To measure your
heart rate,
stop
pedaling
and
place your thumb
on the pulse sen-
sor.
Do not
press too hard,
or the circula-
tion in your
thumb will be restricted and your pulse will not
be detected.
After a few seconds, the heart-
shaped indicator in the display will flash
steadily
,
two dashes will appear, and then your heart rate
will be shown. Hold your thumb on the pulse sen-
sor for about 15 seconds for the most accurate
reading.
If the displayed heart rate appears to be too high
or too low, or if your heart rate is not displayed, lift
your thumb off the pulse sensor for a few seconds.
Then, place your thumb on the pulse sensor as
described above.
Make sure you are applying the proper amount of
pressure to the pulse sensor. Try the pulse sensor
several times until you become familiar with it.
Remember to remain still while measuring your
heart rate.
6.
When you are finished exercising, the console
will turn off automatically.
If the pedals do not move for a few seconds, the
time will flash in the display and the console will
pause. If the pedals do not move for a few min-
utes, the console will turn off and the display will
be reset.