Whirlpool CGM2751KQ Installation Instructions - Page 10

c °nqn;Co ;;en u

Get Whirlpool CGM2751KQ PDF manuals and user guides View all Whirlpool CGM2751KQ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Three-wire connection... Three-wire receptacle Where local codes permit connecting cabinet-ground conductor 4. Loosen or remove center terminal block screw, to neutral wire: ocS;°nqn;Co ;;eneu< %eJ h the center, silver-colored terminal screw of the terminal block, Tighten screw, 6. Connect the other wires to outer terminal block screws, Tighten screws, 7. Tighten strain relief screws, i*_"'_i 8. Insert tab of terminal block cover into slot of dryer rear panel, Secure cover with hold-down screw, __i _ - _,_, _._. Page 1O Where local codes permit connecting cabinet-ground conductor 4. Loosen or remove center, terminal block screw. to neutral wire: 5. Place the hooked end of the neutral wire (white or center) of power supply cable under the center screw of the terminal block (hook facing right). Squeeze hooked end together. Tighten screw. 6. Place the hooked ends of the other power supply cable wires under the outer terminal block screws (hook facing right). Squeeze hooked endstogether. Tighten _=-%, 7.screTwigsh. ten strain relief screws. 8. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. _ -_

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
Three-wire
connection...
Page
1O
Three-wire
receptacle
Where local codes permit
connecting
cabinet-ground
conductor
to neutral
wire:
4.
Loosen or remove center
terminal
block
screw,
oS;
c °nqn;Co ;;en u
%eJ h
e<
the center, silver-colored
terminal
screw of the terminal block,
Tighten
screw,
6.
Connect
the
other
wires to
outer
terminal
block
screws,
Tighten
screws,
7.
Tighten strain relief screws,
i*_"'_i
8.
Insert
tab
of
terminal
block
__i
_
cover
into
slot
of
dryer
rear
panel,
-
_,_,
Secure
cover
with
hold-down
_._.
screw,
Where local codes permit
connecting
cabinet-ground
conductor
to neutral
wire:
4.
Loosen or remove
center,
terminal
block
screw.
5.
Place
the
hooked
end
of the
neutral
wire
(white
or center)
of
power
supply
cable
under
the
center
screw
of the
terminal
block
(hook
facing
right).
Squeeze
hooked
end
together.
Tighten
screw.
6.
Place
the
hooked
ends
of the
other
power
supply
cable
wires
under
the
outer
terminal
block
screws
(hook
facing
right).
Squeeze
hooked
endstogether.
Tighten
_=-%,
screws.
7.
Tighten
strain
relief
screws.
8.
Insert
tab
of
terminal
block
cover
into
slot
of dryer
rear
panel.
Secure
_
-_
cover
with
hold-down
screw.