Whirlpool CGM2751KQ Installation Instructions - Page 11

Three-wire

Get Whirlpool CGM2751KQ PDF manuals and user guides View all Whirlpool CGM2751KQ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Three-wire connection... Three-wire receptacle Where local codes Do Not permit connecting cabinet-ground conductor to neutral wire: 4. Remove center terminal block screw. 9. After realtaching the terminal cover, connect a separate copper ground wire from the external ground connector screw to an adequate ground. 5. Remove the appliance harness ground wire (green with yellow \ stripes) from the external ground connector screw. Connect appliance harness ground wire and the neutral wire (white or center) of the power supply cord/cable under the center, silver-colored terminal block screw. Tighten screw. = terminal block screws. Tighten screws. 7. Tighten strain relief screws. _ 8.Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. " "_ mTo exhaust dryer, see Exhaust requirements, Pages 3-4, Connect exhaust vent to dryer exhaust outlet and exhaust hood using 4" (10,2 cm) clamps, Use caulking to seal exterior wall opening around exhaust hood, m Carefully move dryer into final position, Place level on top of the dryer, first side to side; then front to back, If the dryer is not level, adjust the legs of the dryer up or down until the dryer is level, 1 U • In U,S, or Canada, plug power supply cord into grounded outlet, Or, in the U,S, only, connect direct wire to power supply, Turn power supply on, 1 • Check dryer operation (some accumulated time may be on the timer due to factory testing), Insert coins in slide and press slide in slowly, (Operating time will accumulate per number of coins and Iype of timing cam used,) Push START/RESTARTbulffon, Using a full heat cycle (not the air cycle), let the dryer run for at least five minutes, Dryer will stop when time is used up, Note: Dryer door must be closed for dryer to operate, When door is open, dryer stops, but timer continues to run, To restart dryer, close door and push START/RESTARTbulffon, 2 • If drying time is too long, make sure lint screen is clean, 3m Now start the dryer and allow it to complete a full heat cycle (not air cycle) to make sure it is working properly, Page 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
Three-wire
connection...
Three-wire
receptacle
Where local codes Do Not permit
connecting
cabinet-ground
conductor
to neutral
wire:
4.
Remove
center
terminal
block
screw.
9.
After
realtaching
the
terminal
cover,
connect
a separate
copper
ground
wire
from
the
external
ground
connector
screw
to
an
adequate
ground.
5.
Remove
the
appliance
harness
ground
wire
(green
with
yellow
\
stripes)
from
the
external
ground
connector
screw.
Connect
appliance
harness
ground
wire
and
the
neutral
wire
(white
or center)
of
the
power
supply
cord/cable
under
the
center,
silver-colored
terminal
block
screw.
Tighten
screw.
=
terminal
block
screws. Tighten
screws.
7. Tighten
strain relief screws.
_
"
"_
8.
Insert
tab
of terminal
block
cover
into slot of dryer rear panel.
Secure
cover
with hold-down
screw.
mTo exhaust
dryer,
see Exhaust
requirements,
Pages
3-4, Connect
exhaust
vent
to dryer
exhaust
outlet
and
exhaust
hood
using 4" (10,2 cm)
clamps,
Use caulking
to seal exterior
wall
opening
around
exhaust
hood,
m Carefully
move
dryer
into
final
position,
Place
level on top
of the
dryer,
first side to side; then
front
to
back,
If the
dryer
is not
level,
adjust
the
legs of the
dryer
up or down
until
the
dryer
is level,
1U
•
In
U,S, or Canada,
plug
power
supply
cord
into grounded
outlet,
Or, in the
U,S, only,
connect
direct
wire to power
supply,
Turn power
supply
on,
1
• Check
dryer
operation
(some
accumulated
time
may
be on the
timer
due to factory
testing),
Insert coins
in
slide and
press slide in
slowly,
(Operating
time
will
accumulate
per number
of coins
and
Iype
of timing
cam
used,)
Push
START/RESTARTbulffon,
Using a full
heat
cycle
(not
the
air cycle),
let the
dryer
run for at least five
minutes,
Dryer will stop
when
time
is used
up,
Note:
Dryer door
must be
closed
for
dryer
to operate,
When
door
is open,
dryer
stops, but
timer
continues
to run,
To restart
dryer,
close
door
and
push
START/RESTARTbulffon,
2
• If drying
time
is too
long,
make
sure lint screen
is clean,
3m
Now
start the
dryer
and
allow
it to complete
a full heat
cycle
(not
air cycle)
to make
sure it is working
properly,
Page
11