Whirlpool LEV4634JQ Installation Instructions - Page 4

See installationstepsfor details.

Get Whirlpool LEV4634JQ PDF manuals and user guides View all Whirlpool LEV4634JQ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

See installationstepsfor details. E, Check that dryer is level. B, Remove tape, DI Change door swing. E Check operation. F. Turn on power supply. Cn Disconnect power supply. Make electrical connection. Install feet. SLIDE DRYER ONTO CARDBOARD OR HARDBOARD BEFORE MOVING ACROSS TO PREVENT FLOOR DAMAGE. A. EN Connect vent to dryer. Install vent system. PanelC l m Put on safety glasses and gloves• • Install exhaust _ "_ hood. Use caulking compound to seal exterior wall opening around exhaust hood. m Connect exhaust vent to hood• (Exhaust vent MUST fit inside hood•) Secure vent to hood with clamp• m Run exhaust vent to dryer location. Use the straightest path possible. (See Panel B.) Use clamps to seal all joints. Excessive Weight Hazard Use two or more people to move and install dryer, Failure to do so could result in back or other injury. diamond marking • Remove tape from dryer cabinet. Open dryer door and remove tape from dryer drum. (Not all dryer drums are taped.) Remove drying rack, if included. Turn dryer drum counterclockwise to make sure all tape was removed. Wipe drum with damp cloth to remove any dust. u Start to screw legs into holes by hand. Use an adjustable wrench or I" hex-head socket wrench to finish turning legs untir you reach the ridge with the diamond marking. n Take two cardboard corners from dryer car[on and place them on floor in back of dryer. Firmly grasp body of dryer and gently lay it on its back on the cardboard corners. 1 Stand dryer up on cardboard or hardboard.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
See installationstepsfor details.
E,
B,
Check that
Remove tape,
dryer
is level.
E
Check operation.
F.
Turn
on
power
supply.
DI
Change
door
swing.
Cn
Disconnect
power
supply.
Make electrical connection.
SLIDE DRYER ONTO
CARDBOARD
OR
HARDBOARD
BEFORE
MOVING
ACROSS TO
PREVENT FLOOR
DAMAGE.
Install
feet.
EN
Connect vent
to
dryer.
A.
Install vent system.
l
m
Put on safety glasses and gloves•
•
Install exhaust
_
"_
hood.
Use
caulking
compound
to seal exterior
wall
opening
around
exhaust
hood.
m
Connect
exhaust vent to
hood•
(Exhaust vent
MUST fit
inside
hood•)
Secure
vent to hood with
clamp•
m
Run exhaust
vent
to
dryer
location.
Use
the
straightest
path possible. (See Panel B.)
Use clamps to
seal
all joints.
Excessive
Weight Hazard
Use two or more people to move and
install dryer,
Failure
to
do so could result in back or
other
injury.
•
Remove tape from
dryer
cabinet.
Open dryer door
and remove
tape from
dryer
drum.
(Not
all dryer drums
are taped.)
Remove
drying
rack, if included.
Turn dryer drum
counterclockwise
to make sure all tape was
removed.
Wipe drum
with
damp
cloth
to
remove any dust.
diamond
marking
u
Start to screw legs into
holes by hand.
Use
an adjustable
wrench
or I"
hex-head
socket wrench
to finish turning
legs untir you
reach the ridge with
the diamond
marking.
n
Take two cardboard
corners
from
dryer
car[on and place them
on floor
in
back of dryer.
Firmly grasp body of dryer
and gently
lay it on
its back on the
cardboard
corners.
1
Stand dryer
up on
cardboard
or
hardboard.
PanelC