Whirlpool LEV4634JQ Installation Instructions - Page 6

Where local codes permit, codespermit, codes Do Not permit

Get Whirlpool LEV4634JQ PDF manuals and user guides View all Whirlpool LEV4634JQ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

Three-wire receptacle Where local codes permit connecting cabinet-ground conductor to neutral wire: 4. Loosen or remove block screw, _. Connect the neutral wire center) of power supply cord to the center, silver-colored terminal screw of the terminal block. Tighten screw• OI 6. Connect the other wires to outer _ terminal block screws. Tighten screws. Three wire power supply cord must have three, No.-10 copper wires and match a three-wire receptacle of NEMA Type I0-30R. 7, Tighten strain relief screws. 8. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold down screw. wire reenter) Where local codes permit connecting cabinet-ground conductor 1o neutral wire: 4. Loosen or remove center terminal block screw. 5. Place the hooked end of the neutral wire (white or center) of power supply cable under the center screw of the terminal block (hook facing right). Squeeze hooked end together. 7]ghten screw. 6, Place the hooked ends of the other power supply cable wires under the outer terminal block screws (hook facing right). Squeeze hooked ends together. Tighten screws. 7. Tighten strain relief screws_• 8. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. I i Three-wire power supply cord must have three, No.-10 copper wires and match a three-wire receptacle of NEMA Type 10- SOR. Direct wire power supply cab e mus be , of the three wire connection direct-wge prepared as shown in "Preparing the wire" steps above. Where local codes Do Not permit connecting cabinet-ground conductor to neutral wire: 4. Remove center terminal block screw, 9. After reattaching the terminal cover, connect a separate copper ground wire from the external ground connector screw to an adequate ground. 5, Remove the appliance harness ground wire (green with yellow stripes) from the external ground connector screw. Connect appliance harness ground wire and the neutral wire (white or center) of the power supply cord/cable under the center, silver-colored terminal block screw. Tighten screw, 6. Connect the other wires to outer terminal block screws, Tighten screws. 7, Tighten strain relief screws._ 8,1nsert tab of terminal block cover into __ slot of dryer rear panel. Secure cover with _ hold-down screw, cover with .If"'_f" " _ Panel E

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
Three
wire
power
supply
cord
must
have
three,
No.-10
copper
wires
and
match
a
three-wire
receptacle
of
NEMA
Type
I0-30R.
Three-wire
receptacle
Where local codes permit
connecting
cabinet-ground
conductor
to neutral
wire:
4.
Loosen
or remove
block
screw,
_.
Connect
the
neutral wire
center)
of power supply
cord
to
the
center, silver-colored
terminal
screw of
the
terminal
block. Tighten
screw•
6.
Connect
the other wires to outer _
terminal
block screws. Tighten
screws.
7,
Tighten
strain
relief
screws.
8.
Insert tab of terminal
block cover into
slot of dryer
rear panel.
Secure cover with
hold
down
screw.
OI
wire
reenter)
Where local
codespermit
connecting
cabinet-ground
conductor
1o neutral
wire:
4.
Loosen or remove
center terminal
block screw.
5.
Place the
hooked
end of the neutral
wire (white
or
center)
of power
supply
cable under the center screw of the
terminal
block (hook
facing right).
Squeeze hooked
end together.
7]ghten
screw.
6,
Place
the
hooked
ends
of
the
other
power
supply
cable
wires
under
the
outer
terminal
block
screws
(hook
facing
right).
Squeeze
hooked
ends
together.
Tighten
screws.
7.
Tighten
strain
relief
screws_•
8.
Insert tab of
terminal
block cover into
slot of dryer
rear panel. Secure cover with
hold-down
screw.
I
i
Three-wire
power supply cord
must have
three,
No.-10
copper wires and match
a
three-wire
receptacle
of NEMA Type 10-
SOR.
Direct
wire
power
supply
cab e
mus
be
prepared
as
shown
in
"Preparing
the
wire"
,
of the
three
wire
connection
direct-wge
steps
above.
Where local
codes Do Not permit
connecting
cabinet-ground
conductor
to neutral
wire:
9.
After reattaching
the terminal
cover,
connect
a separate copper
ground
wire from
4.
Remove center terminal
block
screw,
the external
ground
connector
screw to an
adequate
ground.
5,
Remove the appliance
harness ground
wire
(green with
yellow
stripes)
from
the
external
ground
connector
screw.
Connect
appliance
harness ground
wire
and the
neutral wire (white
or center)
of
the power
supply
cord/cable
under the
center, silver-colored
terminal
block screw.
Tighten
screw,
6.
Connect
the other wires to outer
terminal
block screws, Tighten
screws.
7, Tighten
strain relief screws._
8,1nsert
tab of terminal
block cover into
__
.If"'_f" "
slot of dryer
rear panel.
Secure
cover with
_
_
hold-down
screw,
cover with
Panel
E