Whirlpool LEV4634JQ Installation Instructions - Page 8

Kits Make Installation, order

Page 8 highlights

1 Plug power supply cord into grounded outlet or connect direct wire to power supply. Turn power supply on. 11 Check that you: If did not skip any steps. installed all parts. I/propedy installed dryer legs. 11/ leveled dryer. _ i- lJ have all the tools you started with. ' m Read the Use and Care Guide to fully understand your new dryer. Select a full heat cycle (not the air cycle) and start dryer. After five minutes, open dryer door. You should feel heat inside dryer. If dryer does not operate properly, check the following: I,/ electrical supply is connected. i If house fuse is intact and tight; or circuit breaker has not tripped. ' kd dryer door is dosed. If controls are set in a running or "On" position. Ill start button has been pushed firmly. If dryer makes an unusual noise, check the following: If dryer is level. Kits Make Installation Easy clearance between dryer and wall • Total kit length 8 ]eet Part#4396025 eAdditional vent can be snapped between sections for longer runs Kit Contains: 2- 4' ventsectionswith attached close elbows 1- Wall plate for close clearanceinstallations 2- 4" clamps %s easy as 1-2 3" • Provides 2 1/2" clearance between dryer and wall • Great for closet installations • 0"-18", 19"-29" or 29"- 50" periscopes include one male cJlap-lockfitting, one extra long draw-band collar and one clamp e'.18-: Part #439m_7 le'.29.: part #4398011 2_'-50" : Part #439_014 0"-18" Periscope r,4 . • Use when vent outlets overlap or are offset _ • Excesslength can be trimmed to fit _Part #43960_7 18".29"and 29"-50" Per_cope Swivelcolla_ wall connection scantac@ same or opposite For more information, or to easily place your order, call 1-800-442-9991 To have your venting professionally installed, call 1-800-253-1301 for the nearest authorized service provider. Step 1 Olamp One _lbow/veNt section to wall _nd One to dryer, Step 2 E×teNd vent upwar(k almost to top of dryer, then push dryer to wall. Step 3 From over the toP, snap vBnt totJether Dura Safe and Sure (/ollnect are Trademarks of WhlrlDool U _ A Telescoping sections Beveled edges InStallat ion_ 18"-29" : Part #4396011 Swivel collar Extralong fordrper connection 2S"-56": Part #4396014 Panel G

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9

11
Check that
you:
If
did not skip any
steps.
installed
all
parts.
I/propedy
installed
dryer
legs.
11/ leveled dryer.
_
i-
lJ
have all the tools
you
started with.
'
1
Plug power
supply
cord into grounded
outlet
or connect
direct
wire to power
supply.
Turn power supply
on.
m
Read the
Use and Care Guide to fully
understand
your
new dryer. Select a full heat
cycle (not the air cycle) and start dryer. After
five minutes,
open dryer door. You should feel
heat inside dryer.
If dryer
does not
operate
properly,
check the
following:
I,
/
electrical
supply
is connected.
i
If
house fuse is intact
and tight;
or circuit
breaker
has not tripped.
'
kd
dryer
door
is dosed.
If
controls
are set in a running
or "On"
position.
Ill
start button
has been pushed firmly.
If dryer
makes an unusual
noise, check the
following:
If
dryer
is level.
Kits Make Installation
Easy
clearance between
dryer
and wall
• Total kit length
8
]eet
eAdditional
vent
can
be snapped between
Part#4396025
sections for
longer runs
Kit Contains:
2- 4' ventsectionswith
attached
closeelbows
1- Wall plate for close clearanceinstallations
2- 4" clamps
%s easy as 1-2 3"
Step
1
Step
2
Step
3
Olamp
One
E×teNd vent
From over
the
_lbow/veNt
upwar(k
almost
toP,
snap
vBnt
section
to
wall
to top of dryer,
totJether
_nd One to
then
push
dryer
dryer,
to
wall.
Dura
Safe
and
Sure
(/ollnect
are Trademarks
of WhlrlDool
U_A
Provides 2 1/2" clearance
between dryer and wall
Great for closet
installations
0"-18",
19"-29"
or
29"- 50" periscopes
include
one
male
cJlap-lock
fitting,
one extra long
draw-band collar
and one clamp
e'.18-:
Part #439m_7
le'.29.:
part #4398011
2_'-50"
:
Part
#439_014
0"-18" Periscope
r,4
.
Use when vent outlets
overlap or are offset
_
Excesslength can
be trimmed
to fit
_Part
#43960_7
18".29"and
29"-50" Per_cope
Swivelcolla_
wall
connection
scantac@
same or
opposite
Telescoping
Swivel
collar
sections
Beveled edges
InStallat ion_
18"-29" : Part #4396011
Extralong
fordrper
connection
2S"-56": Part #4396014
For
more
information,
or to
easily
place
your
order,
call
1-800-442-9991
To have your venting
professionally
installed,
call
1-800-253-1301
for the
nearest
authorized
service
provider.
Panel G