Whirlpool WED8300SB Use and Care Manual - Page 20
Cycle tips, Dry most loads using the preset cycle settings. - features
UPC - 883049064604
View all Whirlpool WED8300SB manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 20 highlights
NOTE: Dryness level selections can be made only while using Auto Cycles. Selecting More Dry, Normal or Less Dry automatically adjusts the sensed time needed. MOREDRY NORMAL Y DRYNESS Auto Cycles Auto Dry cycles take the guesswork out of drying time and enhance fabric care. The amount of time that is displayed is the estimated time remaining in the cycle. To use a Manual Cycle Point the dial to a Manual Cycle. Press TIMING Up or Down until the desired drying time is displayed. Tap TIMING Up or Down, and the time will change by 1-minute intervals. Press and hold TIMING Up or Down, and the time will change by 5-minute intervals. NOTE: The Timing feature can be used only with Manual Cycles. @® TIMING Press TEMP ADJUST until the desired temperature illuminates. To make changes to Time, Temperature, WRINKLE SHIELD TM feature and Cycle Signal during a Manual Cycle: • Press PAUSE/CANCEL once. • Adjust the Time, Temperature, WRINKLE SHIELD TM feature and End of Cycle Signal. 5. (OPTIONAL STEP) If desired, select WRINKLE SHIELD TM feature. For more details, see "WRINKLE SHIELD TM Feature" in "Additional Features." 6. (OPTIONAL STEP) The Cycle Signal is preset to ON. If desired, you may turn the Cycle Signal OFF. 7. Press and hold START for approximately 1 second until dryer starts. Be sure the door is closed. • If you do not press Start within 5 minutes of selecting a cycle, the dryer automatically shuts off. To pause/stop the dryer at any time Open the door or press PAUSE/CANCEL once. To restart the dryer Close the door. Press and hold START until dryer starts. To cancel your dryer at any time Press PAUSE/CANCEL twice. NOTE: Drying will continue from where the cycle was interrupted if you close the door and press Start within 5 minutes. If the cycle is interrupted for more than 5 minutes, the dryer will shut off. Select new cycle settings before restarting the dryer. This feature allows you to lock your settings to avoid unintended use of the dryer. You can also use the control lock feature to avoid unintended cycle or option changes during dryer operation. To enable the control lock feature: Press and hold END OF CYCLE SIGNAL button for 3 seconds. The LocWUnlock Control icon lights up, and a single beep tone is heard. To unlock, press and hold END OF CYCLE SIGNAL button for 3 seconds. The indicator light turns off. Select the correct cycle and dryness level or temperature for your load. If an Auto Cycle is running, the display shows the estimated cycle time when your dryer is automatically sensing the dryness level of your load. If a Manual Cycle is running, the display shows the exact number of minutes remaining in the cycle. Cool Down tumbles the load without heat during the last few minutes of all cycles. Cool Down makes the loads easier to handle and reduces wrinkling. The length of the Cool Down depends on the load size and dryness level. Drying tips • Follow care label directions when they are available. • If desired, add a fabric softener sheet. Follow package instructions. • Remove the load from the dryer as soon as tumbling stops to reduce wrinkling. This is especially important for permanent press, knits and synthetic fabrics. • Avoid drying heavy work clothes with lighter fabrics. This could cause overdrying of lighter fabrics, leading to increased shrinkage or wrinkling. Cycle tips • Dry most loads using the preset cycle settings. • Refer to the Auto or Manual Preset Cycle Settings chart (in the "Cycles" section) for a guide to drying various loads. Drying temperature and Dryness are preset when you choose an Auto Cycle. You can choose a different dryness level, depending on your load by pressing the DRYNESS button to select MORE DRY or LESS DRY. • If you wish to adjust the cycle length of a Manual Cycle, you must press TIMING Up or Down. Adjust the temperature of a Manual Cycle by pressing TEMP ADJUST until the desired temperature is selected. NOTE: You cannot choose a Dryness Level with Manual Cycles. 20