Whirlpool WET3300SQ User Instructions - Page 3

WARNING Location Requirements Washer/Dryer Dimensions Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from dryer. Failure to do so can result in death, explosion, or fire. 71⁵⁄₈" (181.9 cm) 23³⁄₄" (60.3 cm) 32¹⁄₄" (81.9 cm) You will need ■ A location that allows for proper exhaust installation. See "Venting Requirements." ■ A separate 30-amp circuit. ■ If you are using a power supply cord, a grounded electrical outlet located within 2 ft (61 cm) of either side of the washer/ dryer. See "Electrical Requirements." ■ A sturdy floor to support the washer/dryer weight (washer/ dryer, water and load) of 500 lbs (226.8 kg). ■ A level floor with a maximum slope of 1" (2.5 cm) under entire washer/dryer. Clothes may not tumble properly and automatic sensor cycles may not operate correctly if washer/dryer is not level. Installing on carpet is not recommended. ■ A water heater set to deliver 120°F (49°C) water to the washer. ■ Hot and cold water faucets located within 4 ft (1.2 m) of the hot and cold water fill valves, and water pressure of 5-100 psi (34.5-689.6 kPa). The washer/dryer must not be installed or stored in an area where it will be exposed to water and/or weather. Do not operate your washer in temperatures at or below 32ºF (0ºC). Some water can remain in the washer and can cause damage in low temperatures. See "Washer/Dryer Care" in the Washer/Dryer User Instructions for winterizing information. Do not operate your dryer at temperatures below 45°F (7°C). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. This can result in longer drying times. Check code requirements. Some codes limit, or do not permit, installation of the washer/dryer in garages, closets, mobile homes or sleeping quarters. Contact your local building inspector. Installation Clearances The location must be large enough to allow the dryer door to open fully. *32" (81.3 cm) 27" (68.6 cm) *Most installations require a minimum 5" (12.7 cm) clearance behind the dryer for the exhaust vent with elbow. See "Venting Requirements." Installation spacing for recessed area or closet installation The following spacing dimensions are recommended for this washer/dryer. This washer/dryer has been tested for spacing of 0" (0 cm) clearance on the sides. Recommended spacing should be considered for the following reasons: ■ Additional spacing should be considered for ease of installation and servicing. ■ Additional clearances might be required for wall, door and floor moldings. ■ Additional spacing on all sides of the washer/dryer is recommended to reduce noise transfer. ■ For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable. 6" (15.2 cm) 48 in.2 (310 cm2) 3" (7.6 cm) 24 in.2 (155 cm2) 1" 27" 1" 1"* 32" 5"** (2.5 cm) (68.6 cm) (2.5 cm) (2.5 cm) (81.3 cm) (12.7 cm) A B C 3" (7.6 cm) A. Recessed area B. Side view - closet or confined area C. Closet door with vents *Required spacing **Rear clearance may be 1" (2.5 cm) when house exhaust system is lined up directly with dryer exhaust. Mobile Home - Additional Installation Requirements This washer/dryer is suitable for mobile home installations. The installation must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280) or the Canadian Manufactured Home Standard, CAN/CSA-Z240 MH. 3