Whirlpool WFC8090GX Installation Instructions - Page 18

Reinstalling/using, Washer/dryer Again, Transporting Your Washer/dryer

Get Whirlpool WFC8090GX PDF manuals and user guides View all Whirlpool WFC8090GX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

TRANSPORTING YOUR WASHER/DRYER 1. Shut off water faucet. Disconnect and drain water inlet hose. 2. If washer/dryer will be moved during freezing weather, follow "Winter Storage Care" directions before moving. 3. Disconnect drain hose from drain system and from back of washer/dryer. 4. Unplug power cord. 5. Place inlet hose and drain hose inside drum. 6. Bundle power cord with a rubber band or cable tie to keep it from hanging onto the ground. IMPORTANT: Call for service to install new transport bolts. Do not reuse transport bolts. Washer/dryer must be transported in the upright position. To avoid structural damage to your washer/dryer, it must be properly set up for relocation by a certified technician. REINSTALLING/USING WASHER/DRYER AGAIN To reinstall washer/dryer after non-use, vacation, winter storage, or moving: 1. Refer to "Installation Instructions" to locate, level, and connect washer/dryer. 2. Before using again, run washer/dryer through the following recommended procedure: To use washer/dryer again: 1. Flush water pipes and hose. Reconnect water inlet hose. Turn on water faucet. 2. Plug in washer/dryer or reconnect power. 3. Run washer/dryer through Heavy Duty wash cycle to clean washer/dryer and remove antifreeze, if used. Use only HE detergent. Use half the manufacturer's recommended amount for a medium-size load. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
18
REINSTALLING/USING
WASHER/DRYER AGAIN
To reinstall washer/dryer after non-use, vacation, winter
storage, or moving:
1.
Refer to “Installation Instructions” to locate, level, and
connect washer/dryer.
2.
Before using again, run washer/dryer through the
following recommended procedure:
To use washer/dryer again:
1.
Flush water pipes and hose. Reconnect water inlet
hose. Turn on water faucet.
2.
Plug in washer/dryer or reconnect power.
3.
Run washer/dryer through Heavy Duty wash cycle
to clean washer/dryer and remove antifreeze, if used.
Use only HE detergent. Use half the manufacturer’s
recommended amount for a medium-size load.
TRANSPORTING YOUR WASHER/DRYER
1.
Shut off water faucet. Disconnect and drain water inlet
hose.
2.
If washer/dryer will be moved during freezing weather,
follow “Winter Storage Care” directions before moving.
3.
Disconnect drain hose from drain system and from back
of washer/dryer.
4.
Unplug power cord.
5.
Place inlet hose and drain hose inside drum.
6.
Bundle power cord with a rubber band or cable tie
to keep it from hanging onto the ground.
IMPORTANT:
Call for service to install new transport
bolts. Do not reuse transport bolts. Washer/dryer must
be transported in the upright position. To avoid structural
damage to your washer/dryer, it must be properly set up
for relocation by a certified technician.