Whirlpool WFC8090GX Installation Instructions - Page 43

Error Code Appears in Display cont.

Get Whirlpool WFC8090GX PDF manuals and user guides View all Whirlpool WFC8090GX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

TROUBLESHOOTING First try the solutions suggested here or visit our website at www.whirlpool.com/owners (in Canada www.whirlpool.ca/owners) for assistance and to possibly avoid a service call. If you experience Possible Causes Solution Error Code Appears in Display (cont.) Once any possible issues are corrected, touch the POWER button once to clear the code. Re-select and restart the cycle. F5E4 Door not opened between cycles Three consecutive cycles were run without the door being opened. The washer/dryer will generate an invalid key beep when START is pressed. Open and close the door. Check for obstructed door switch. Verify functionality of door switch. F6E1 Communication failure between electronics in washer/dryer Problem detected with the washer/ dryer electronics. Try resetting the washer/dryer by unplugging it from the outlet and then plugging it back in. If unsuccessful, call for service. F6E2 Communication failure between electronics in washer/dryer Problem detected with the washer/ dryer electronics. Try resetting the washer/dryer by unplugging it from the outlet and then plugging it back in. If unsuccessful, call for service. F8E1 No water flow detected/ fill timeout Washer/dryer may not be connected to the home water supply. Home water supply valve may not be turned on. Inlet hose to washer/dryer may be kinked. Inlet valve on washer/dryer may have failed. Make sure that the washer/dryer is connected to the home cold water supply and that the home water supply valve is turned on. Verify that the inlet hose to the washer/dryer is not kinked. If problem persists, call for service. F8E3 Overflow of water detected Inlet valve on washer/dryer is leaking Call for service. internally. F9E1 Drain timeout/ drain pump failure Drain pump filter on washer/dryer may need to be cleaned. Bellow drain holes in washer/dryer may be obstructed. Washer/dryer drain hose or home drain system may be obstructed. Drain pump on washer/ dryer may have failed. Clean drain pump filter on washer/dryer. Check bellow drain holes in washer/dryer for obstructions. Check washer/dryer drain hose and home drain system for obstructions. If problem persists, call for service. 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
43
TROUBLESHOOTING
If you experience
Possible Causes
Solution
Error Code Appears in Display (cont.)
Once any possible issues are corrected, touch the POWER button once to clear the code. Re-select and restart the cycle.
F5E4
Door not opened
between cycles
Three consecutive cycles were run
without the door being opened. The
washer/dryer will generate an invalid
key beep when START is pressed.
Open and close the door. Check for obstructed door switch.
Verify functionality of door switch.
F6E1
Communication failure
between electronics
in washer/dryer
Problem detected with the washer/
dryer electronics.
Try resetting the washer/dryer by unplugging it from the outlet
and then plugging it back in. If unsuccessful, call for service.
F6E2
Communication failure
between electronics
in washer/dryer
Problem detected with the washer/
dryer electronics.
Try resetting the washer/dryer by unplugging it from the outlet
and then plugging it back in. If unsuccessful, call for service.
F8E1
No water flow detected/
fill timeout
Washer/dryer may not be connected
to the home water supply. Home
water supply valve may not be turned
on. Inlet hose to washer/dryer may be
kinked. Inlet valve on washer/dryer
may have failed.
Make sure that the washer/dryer is connected to the home
cold water supply and that the home water supply valve is
turned on. Verify that the inlet hose to the washer/dryer is not
kinked. If problem persists, call for service.
F8E3
Overflow of
water detected
Inlet valve on washer/dryer is leaking
internally.
Call for service.
F9E1
Drain timeout/
drain pump failure
Drain pump filter on washer/dryer
may need to be cleaned. Bellow
drain holes in washer/dryer may
be obstructed. Washer/dryer drain
hose or home drain system may be
obstructed. Drain pump on washer/
dryer may have failed.
Clean drain pump filter on washer/dryer. Check bellow drain
holes in washer/dryer for obstructions. Check washer/dryer
drain hose and home drain system for obstructions. If problem
persists, call for service.
First try the solutions suggested here or visit our website at
www.whirlpool.com/owners
(in Canada
www.whirlpool.ca/owners
) for assistance and to possibly avoid a service call.