Whirlpool WFW9700VW Use and Care Guide - Page 14

Pausing or Restarting 1. To pause the washer at any time, press PAUSE/CANCEL. 2. To continue the cycle, press START (for approximately 1 second). Add A Garment This washer allows a 4-8 minute period in which other garments may be added to the load. You can add items to the washer if the Add A Garment status light is glowing. To add items when Add A Garment light is glowing 1. Select PAUSE/CANCEL once. The washer door unlocks after a few seconds, and items can be added. 2. To continue the cycle, close the door and select and hold START (for approximately 1 second). To add items when the Add A Garment light is not glowing 1. You must cancel the current cycle by pressing PAUSE/CANCEL twice. This will cancel the wash cycle and options. The washer door unlocks, and items can be added. 2. Close the door, press POWER, and select the new cycle and options. Select and hold START (for approximately 1 second). Changing Cycles, Options, and Modifiers Not all Options and Modifiers are available with all cycles. Available modifiers will glow amber. If an option or modifier is unavailable with a selected cycle, the light will not illuminate. Cycles, Options, and Modifiers can be changed anytime before START is selected. To cancel a cycle and select a new cycle Press PAUSE/CANCEL twice. Press POWER. Select desired cycle. Select the desired Options or modifiers such as Water Temp, Spin Speed, and Soil Level. 5. Press START (for approximately 1 second) to restart the washer at the beginning of the new cycle. 1. 2. 3. 4. Done The Done status light stays on for 60 minutes after the cycle is complete, and then the washer shuts off. To cancel a cycle 1. Press PAUSE/CANCEL twice. 2. The washer powers down, the door unlocks, and clothes can be removed. NOTE: If the water level or the temperature is too high, the washer will drain automatically before the door unlocks. Sanitized This washer has a Sanitize water temperature that is certified by NSF International, an independent third-party testing and certification organization. The certification verifies that the sanitizing cycle reduces 99.9% of bacteria typically found on clothing, bedding, and towels, and there is no carryover of bacteria between loads after the cycle is complete. To change Options or Modifiers after the cycle has started 1. Press PAUSE/CANCEL once. 2. Select the desired Options or modifiers such as Water Temp, Spin Speed, and Soil Level. Available selections will glow amber. 3. Press START (for approximately 1 second) to continue the cycle. Certified to Sanitize To drain the washer manually 1. 2. 3. 4. 5. Press PAUSE/CANCEL twice. Press POWER. Select DRAIN/SPIN. Press START (for approximately 1 second) to begin the drain. When the spin is complete, the door unlocks. Items can be removed from the washer. If the "Sanitize" wash temperature was selected, when the wash cycle is complete, the DONE status light will illuminate, the door unlocks, and the wash load can be removed from the washer. The washer powers down automatically 60 minutes after the cycle is complete and the DONE status light turns off. Only cycles with sanitize wash temperature selected have been designed to meet the requirements of NSF Protocol P172 for Sanitizing Efficacy. Controls Lock/Unlock The Controls Lock avoids unintended use of the washer. You can also use the control lock feature to avoid unintended cycle or option changes during a cycle. When Controls Lock is lit, all buttons are disabled except for Pause/Cancel and Start. You can lock the controls while the washer is operating. To lock the controls Press and hold CONTROLS LOCK/UNLOCK for 3 seconds after the cycle starts, or when the washer is turned off. Status Lights These lights show which portion of the cycle the washer is operating. They also indicate when you can add an additional item to the wash cycle and when the controls are locked. The status light next to the CONTROLS LOCK/UNLOCK button will glow. 14