Whirlpool WFW9700VW Use and Care Guide - Page 5

Whirlpool WFW9700VW - Duet Steam -Front Load Washer Manual

Get Whirlpool WFW9700VW - Duet Steam -Front Load Washer PDF manuals and user guides
UPC - 883049134680
View all Whirlpool WFW9700VW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

Location Requirements Selecting the proper location for your washer improves performance and minimizes noise and possible washer "walk." Your washer can be installed under a custom counter, or in a basement, laundry room, closet, or recessed area. See "Drain System." Companion appliance location requirements should also be considered. Proper installation is your responsibility. You will need

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
5
Location Requirements
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer “walk.”
Your washer can be installed under a custom counter, or in a
basement, laundry room, closet, or recessed area. See “Drain
System.”
Companion appliance location requirements should also
be considered. Proper installation is your responsibility.
You will nee
d
■
A water heater set to deliver 120°F (49°C) water to the washer.
■
A grounded electrical outlet located within 6 ft (1.8 m) of where
the power cord is attached to the back of the washer.
See “Electrical Requirements.”
■
Hot and cold water faucets located within 4 ft (1.2 m)
of the hot and cold water fill valves, and water pressure
of 20-100 psi (137.9-689.6 kPa).
■
If you live in a hard water area, use of a water softener is
recommended to control the buildup of scale in the steamer
and other areas of the washer. Over time, the buildup of lime
scale may clog the steamer, which will reduce steamer
efficiency and performance. Excessive buildup of scale may
lead to the need for steamer replacement or repair.
■
A level floor with a maximum slope of 1" (25 mm) under entire
washer. Installing the washer on soft floor surfaces, such as
carpets or surfaces with foam backing, is not recommended.
■
A sturdy and solid floor to support the washer with a total weight
(water and load) of 400 lbs (180 kg).
Do not operate your washer in temperatures below 32°F (0°C).
Some water can remain in the washer and can cause damage in low
temperatures.
Installation clearances
■
The location must be large enough to allow the washer door
to be fully opened.
■
Additional spacing should be considered for ease of installation
and servicing.
■
Additional clearances might be required for wall, door, and
floor moldings.
■
Additional spacing of 1" (25 mm) on all sides of the washer
is recommended to reduce noise transfer.
■
Companion appliance spacing should also be considered.
Washer Dimensions
27
"
(686 mm)
51
"
(1295 mm)
3
8
"
(965 mm)
3
1½
"
(800 mm)
Recommen
d
e
d
installation spacing for custom
un
d
ercounter installation
The dimensions shown are for the recommended spacing.
Custom un
d
ercounter installation - Washer only
1
"
(25 mm
)
1
"
(25 mm)
3
9
"
min.
(990 mm)
27
"
(686 mm)
Recommen
d
e
d
installation spacing for recesse
d
or closet installation, with or without a pe
d
estal
The dimensions shown are for the recommended spacing.
Recesse
d
area or closet installation
3
4
"
(864 mm)
A
B
3"
(76 mm)
3"
(76 mm)
48 in.
2
*
(
3
10 cm
2
)
24 in.
2
*
(155 cm
2
)
1
"
(25 mm)
4
"
(102 mm)
3
1½
"
(800 mm)
A. Side view - closet or confined area
B. Closet door with vents
*Min. top and bottom air openings for closet door.
Recesse
d
or closet installation - Washer on pe
d
estal
1
"
(25 mm)
3
1½
"
(800 mm)
1
"
(25 mm)
1
"
(25 mm)
27
"
(686 mm)
4
"
(102 mm)
18
"
min.
(457 mm)
A
B
A. Recessed area
B. Side view - closet or confined area