Whirlpool WRF560SFYB Use & Care Guide - Page 8

Handle Installation and Removal - parts

Get Whirlpool WRF560SFYB PDF manuals and user guides View all Whirlpool WRF560SFYB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Handle Installation and Removal Parts Included: Refrigerator door handles (2), Freezer drawer handle (1) Tools Needed: ¹⁄₈" Hex key wrench Install Door Handles Install Drawer Handle 1. With the freezer drawer closed, place the handle on the shoulder screws with the setscrews facing down toward the floor. NOTE: Handle mounting setscrews are preinstalled inside the handle. 1. Remove the handles from the packaging inside the refrigerator. A 2. Open a refrigerator door. On the opposite door, place the handle on the shoulder screws with the setscrews facing the adjacent door. B A A. Shoulder screw B. Setscrews inside the handle B 2. Firmly push the handle toward the drawer until the handle base is flush against the drawer. 3. Insert the short end of the hex key into the left-hand hole and slightly rotate the hex key until it is engaged in the setscrew. A. Shoulder screws B. Setscrews inside the handle 3. Firmly push the handle toward the door until the handle base is flush against the door. 4. While holding the handle, insert the short end of the hex key into the upper hole and slightly rotate the hex key until it is engaged in the setscrew. 5. Using a clockwise motion tighten the setscrew until the screw feels tight. 6. Repeat steps 4 and 5 to fasten the lower setscrew. IMPORTANT: When the screws feel tight, tighten them an additional quarter-turn. The handle is not properly installed without this extra tightening. 7. Repeat steps 2 through 6 to install the other handle onto the adjacent refrigerator door. 4. Using a left to right motion tighten the setscrew a quarter-turn at a time. Repeat until the screw feels tight. 5. Repeat steps 3 and 4 to fasten the right-hand setscrew to the shoulder screw. IMPORTANT: When the screws feel tight, tighten them an additional quarter-turn. The handle is not properly installed without this extra tightening. 6. Save the hex key and all instructions. Remove the Handles 1. While holding the handle, insert the short end of the hex key into a setscrew hole and slightly rotate the hex key until it is engaged in the setscrew. 2. Using a right to left motion loosen the setscrew a quarter-turn at a time. 3. Repeat steps 1 and 2 for the other setscrew. Slowly pull the handle away from the door or drawer. 4. If necessary, use a Phillips screwdriver to remove the shoulder screws from the door. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
8
Handle Installation and Removal
Parts Included:
Refrigerator door handles (2),
Freezer drawer handle (1)
Tools Needed:
¹⁄₈
" Hex key wrench
Install Door Handles
NOTE:
Handle mounting setscrews are preinstalled inside the
handle.
1.
Remove the handles from the packaging inside the
refrigerator.
2.
Open a refrigerator door. On the opposite door, place the
handle on the shoulder screws with the setscrews facing the
adjacent door.
3.
Firmly push the handle toward the door until the handle base
is flush against the door.
4.
While holding the handle, insert the short end of the hex key
into the upper hole and slightly rotate the hex key until it is
engaged in the setscrew.
5.
Using a clockwise motion tighten the setscrew until the screw
feels tight.
6.
Repeat steps 4 and 5 to fasten the lower setscrew.
IMPORTANT:
When the screws feel tight, tighten them an
additional quarter-turn. The handle is not properly installed
without this extra tightening.
7.
Repeat steps 2 through 6 to install the other handle onto the
adjacent refrigerator door.
Install Drawer Handle
1.
With the freezer drawer closed, place the handle on the
shoulder screws with the setscrews facing down toward the
floor.
2.
Firmly push the handle toward the drawer until the handle
base is flush against the drawer.
3.
Insert the short end of the hex key into the left-hand hole and
slightly rotate the hex key until it is engaged in the setscrew.
4.
Using a left to right motion tighten the setscrew a quarter-turn
at a time. Repeat until the screw feels tight.
5.
Repeat steps 3 and 4 to fasten the right-hand setscrew to the
shoulder screw.
IMPORTANT:
When the screws feel tight, tighten them an
additional quarter-turn. The handle is not properly installed
without this extra tightening.
6.
Save the hex key and all instructions.
Remove the Handles
1.
While holding the handle, insert the short end of the hex key
into a setscrew hole and slightly rotate the hex key until it is
engaged in the setscrew.
2.
Using a right to left motion loosen the setscrew a quarter-turn
at a time.
3.
Repeat steps 1 and 2 for the other setscrew. Slowly pull the
handle away from the door or drawer.
4.
If necessary, use a Phillips screwdriver to remove the shoulder
screws from the door.
A. Shoulder screws
B. Setscrews inside the handle
B
A
A. Shoulder screw
B. Setscrews inside the handle
B
A