Xerox M118 System Administration Guide - Page 83

USB Port Communication Setup, Workstation Setup, Select [System Settings].

Get Xerox M118 - WorkCentre B/W Laser PDF manuals and user guides
UPC - 095205219258
View all Xerox M118 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

USB Port Installation USB Port Communication Setup This section describes how to set up USB communication on the machine. The following parameters can be set depending on your requirements. These setups must be done without the USB cable connected. Enable the USB port. NOTE: CentreWare Internet Services can also be used to configure the machine. Refer to CentreWare Internet Services chapter on page 91. 1. Press the button. 2. Select [System Settings]. 3. Enter the password using the numeric keypad and then select [Confirm]. 4. Select [Print Settings] and then press the button. 5. Press the button on the [Network/Port] screen. 6. Select [USB] by selecting [T] or [S] and then press the button. 7. Select [Port Status] by selecting [T] or [S] and then press the button. 8. Select [Enable] by selecting [T] or [S] and then press the button. If necessary, you may change the following settings. • Auto Eject Time • Print Mode • PJL • Adobe Protocol NOTE: Adobe Protocol can be set when the PostScript Kit (optional) has been installed. 9. Press the button. Workstation Setup Before starting Workstation Setup, make sure that the USB cable is disconnected from the computer. Then perform the following steps. 1. Refer to the HTML documentation in CentreWare Utilities CD-ROM or documentation provided with the optional PostScript Kit, and install the print drivers for the machine on all the workstations that will be sending jobs to the machine. 2. Continue with Test Print on page 84. Xerox CopyCentre/WorkCentre 118 System Administration Guide 83

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
USB Port Installation
Xerox CopyCentre/WorkCentre 118 System Administration Guide
83
USB Port Communication Setup
This section describes how to set up USB communication on the machine. The
following parameters can be set depending on your requirements. These setups must
be done without the USB cable connected.
Enable the USB port.
NOTE:
CentreWare Internet Services can also be used to configure the machine.
Refer to
CentreWare Internet Services chapter on page 91.
1.
Press the <Log In/Out> button.
2.
Select [System Settings].
3.
Enter the password using the numeric keypad and then select [Confirm].
4.
Select [Print Settings] and then press the <Enter> button.
5.
Press the <Enter> button on the [Network/Port] screen.
6.
Select [USB] by selecting
[
] or [
] and then press the <Enter> button.
7.
Select [Port Status] by selecting
[
] or [
] and then press the <Enter> button.
8.
Select [Enable] by selecting
[
] or [
] and then press the <Enter> button.
If necessary, you may change the following settings.
•
Auto Eject Time
•
Print Mode
•
PJL
•
Adobe Protocol
NOTE:
Adobe Protocol can be set when the PostScript Kit (optional) has been
installed.
9.
Press the <Log In/Out> button.
Workstation Setup
Before starting Workstation Setup, make sure that the USB cable is disconnected from
the computer.
Then perform the following steps.
1.
Refer to the HTML documentation in CentreWare Utilities CD-ROM or
documentation provided with the optional PostScript Kit, and install the print
drivers for the machine on all the workstations that will be sending jobs to the
machine.
2.
Continue with
Test Print on page 84
.